Impulse Test

The SURGE TEST GENERATOR PG 10-1520 has been designed for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, wave form 8/20 µs, peak value adjustable 0.2 - 10 kA for each output. ...more

The high-current pulse generator PG 6-2402 is designed for surge current testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. It generates standard impulse currents with waveform 8/20µs. Pulse current output amplitude can be set to 2 - 50 kA. ...more

High-voltage pulse generator IPG 2025 / IPG 2436 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. It is designed for testing impulse dielectric strength of components, insulations, air- and surface flash-over gaps acc. to IEC/EN 60664, VDE 0110, VDE 0411, VDE 0420, IEC 6 etc.. ...more

INS-AX2 series simulators are the advanced version of our conventional INS simulators. enabling users to carry out tests in a more automated manner. ...more

The High-Voltage Pulse Generator IPG 255 is designed for testing of impulse dielectric strength of components, insulation, air-and surface flash-over gaps of watt-hour meters, static relais etc. according to IEC 255, EN 61036, VDE 0435 Teil 303. ...more

The high-current pulse generators PG 6-200 / PG 6-400 are designed for surge testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. They generate standard impulse currents with waveform 8/20 µs. Short circuit output current amplitude is selectable from 0.2 up to 10 kA by adjustment of the chargin ...more

The LDS Nicolet Sigma 100HV has the perfect combination of speed and resolution for your toughest electrical applications, from lightning impulse testing to switchgear measurements to power conversion. This high voltage scope includes up to eight channels of 100 MS/s 12-bit digitizers per channel, 25 MHz bandwidth, 1 MegaWord memory per channe ...more

The high-voltage impulse generator PG 4-640 generates standard impulse voltages with waveforms 10/700 µs. Output voltage is adjustable between 0.1 kV and 4 kV. It is designed for simultaneous testing of several ports of telecom equipment acc. to ITU specification K20. ...more

Measuring & Conversion DIN-IEC 688. Dielectric Strength DIN-IEC 688 2K Vac 50/60 hz /1minute. Impulse test ANSI C37.90a/ 1974, IEEE 587/ 1983, IEC 255-4, 5KV (1.2 x 50ms).  Surge test (ring wave) IEC 255-4(2.5KV - 0.25ms/1 Mhz) ...more

This equipment as a Lightning Impulse Simulation Tester has to pass the shock wave immobility efficiency test on all switches(NFB, magnet, the circuit breaker), lightning arrester, surge arrester, etc, according to the technique standard on electric apparatus of the Korean Eectric Safety Management Asociation, which stipulates that there must ...more

The 7720 Impulse Winding Tester uses a very high voltage impulse to stimulate the device under test (DUT).  It analyzes the decay waveform to detect changes in material, shorted and damaged windings and other errors.  Long term decay of a winding can also be detected. ...more

The LDS Nicolet Sigma 100HV has the perfect combination of speed and resolution for your toughest electrical applications, from lightning impulse testing to switchgear measurements to power conversion. This high voltage scope includes up to eight channels of 100 MS/s 12-bit digitizers per channel, 25 MHz bandwidth, 1 MegaWord memory per channel ...more

The SURGE TEST GENERATOR PG 10-10000 delivers surge current pulses with the waveform 8/20µs, acc. to IEC 60. It was designed for testing surge protection devices. Moreover the generator can be used for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, peak value adjustable 0.5 ...more

IWT-5000(Impulse Winding Tester) is the advanced design of the test instrument for the insulation performance of the coil. It is used to test the coil wire material, magnetic material, framework and process craft whose can influence debasement of the insulation performance of the coil layer, circle and down-lead. ...more

The surge current generators PG **-**** generate impulse currents with wave form 10/50 µs - 10/1000 µs acc. to IEC, VDE etc.. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generator is designed for testing electrical components, overvolta ...more

HV - Impulse generators IPG 605, IPG 1012 and IPG 1218 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. They are designed for testing impulse dielectric strength of components, insulations, air- and surface flash-over gaps acc. to IEC/EN 60664, VDE 0110, VDE 0411, VDE 0420, IEC 6 etc.. ...more

The front-chopped-wave generator IPG 506 is used for measuring dc spark-over voltage and impulse spark-over voltage of over-voltage protectors acc. to CCITT / ITU-T, K12. A linearly rising voltage, rate of rise 100 V/s up to 637.5 V, is connected to the device under test. The spark-over voltage measured is shown in the display ...more

For the generation of high voltage lightning and switching impulses according to IEC 60060 for indoor and outdoor use. Impulse voltage generator, charging and control unit, control and measuring system, chopping gaps  ...more

The PP30 PowerPack is a high power impulse generator used to test very large high voltage windings. The output is controlled by a variable transformer from 2000 volts up to a maximum of 30,000 volts. ...more

The SURGE TEST GENERATOR PG 10-1520 has been designed for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, wave form 8/20 µs, peak value adjustable 0.2 - 10 kA for each output. ...more

The high-current pulse generator PG 6-2402 is designed for surge current testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. It generates standard impulse currents with waveform 8/20µs. Pulse current output amplitude can be set to 2 - 50 kA. ...more

The High-Voltage Pulse Generator IPG 1201 is designed for testing of impulse dielectric strength of components, insulation, air-and surface flash-over gaps. It is specially used for testing surge withstand capability of insulation between accesible parts and hazardous live parts, e.g. terminals for connection of antenne and mains supply tremina ...more

The D30R/D40R is a high performance stand alone impulse generator specifically designed to diagnose faults in very large electrical motors and windings, improving quality in the shop and reducing necessary and costly downtime in the field.  ...more

The surge current generators PG **-**** generate impulse currents with wave form 10/50 µs - 10/1000 µs acc. to IEC, VDE etc.. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generator is designed for testing electrical components, overvolta ...more

The high-voltage pulse generator PG 10-700c creates standard impulse voltages with waveforms 1.2/50 µs and 10/700 µs. It is designed for dielectric testing of components and systems as well as testing of the electromagnetic compatibility of electronic systems and devices acc. to CCITT-K17/K20/K22, IEC 1000-4-5, VDE 0847 etc ...more