ISO

The 180 Electrical Safety Analyzer is a lightweight and ultra-portable test device for ECG-device-leakage and isolation testing. ...more

Variable Isolated AC Power Supply. Model 1653A is a compact, rugged unit. Variable isolated 0 to 150 VAC. 2A continuous output. Displays voltage or current readings. Isolation transformer to eliminate shock hazard while servicing "hot chassis" equipment ...more

Variable Isolated AC Power Supply. Model 1655A displays V, A, VA and leakage. Variable isolated output 0 to 150 VAC.# 3A continuous, 4A intermittent output# Built in soldering iron temperature control# Expanded leakage scale# Circuit breaker overload protection# Displays V, A, VA, leakage ...more

NSG 438 ESD simulator comprehensively fulfills virtually all international standard requirements and supports proposed future standards. Air and contact discharge 200V to 30kV. Touch panel display controlled. Battery powered. Compliant with all known standards (IEC, ANSI, SAE, ISO, MIL etc). Interchangeable network modules. Discharge detector. ...more

# Use Model 1604A for safe testing of transformerless equipment. Leakage: less than 0.1 mA# Output Voltage: 117 to 124 V nominal (120 V input)# Output Current: 1.25 A continuous ...more

The PX468S provides four precision four-wire voltage references in a single-wide M-module format. Each voltage reference is independent and individually optically isolated to allow independent thermocouple simulation. An on-board microcontroller provides precise control of the voltage references, including automatic temperature compensation. This u ...more

The MSXB 084 Isolated Analog Input Expansion Board provides isolated analog inputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew. ...more

The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew. ...more

The Microstar Laboratories Isolated Digital Expansion Board, part number MSXB 078, provides isolated digital expansion for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing errors from high-channel count digital I/O. ...more

The Microstar Laboratories Isolated 16-Bit Analog Output Board, part number MSXB 076, provides isolated analog outputs for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – as well as to eliminate phase errors from analog outputs in your ap ...more

Model 4860A GPIB Bus Isolated Expander provides 2000 volts of isolation between two GPIB buses and drives up to 14 additional bus devices. Automatically locates Bus talker to eliminate address switches. IEEE-488.2 compatible. ...more

Serial to Analog Minibox. Provides 4 isolated Analog Outputs, 4 isolated Analog Inputs, 4 200 mA Drivers and 6 Digital Inputs. RS-232 and RS-485 serial interface provides GPIB functionality over a serial link. ...more

The 28208 Octal Thermocouple Conditioner provides eight channels of conditioning for thermocouples or other DC and AC voltage inputs. The 28208 consists of a low-drift programmable differential pre-amplifier, a 3-pole programmable filter and a programmable post-amplifier. A rugged remote isothermal block with digital temperature sensor provide ...more

27304 Quad Dual-Mode Charge Amplifier supports the two common piezoelectric transducer types, charge and voltage (IEPE), providing flexibility for use in a wide range of applications including vibration measurements. Programmable gain of up to x4096 is provided. The 27304 accommodates both isolated and grounded inputs. For integrated circuit p ...more

The V450 is a VME 16-channel isolated analog-to-digital converter module which can acquire a wide range of DC voltages, including thermocouple temperatures. Each channel is independent with an isolated DC power supply, optoisolated interface, A/D converter, signal conditioning, input protection circuits, and test relay. An internal microproces ...more

The Diagnostic-Tool is a universal software application, compliant with ISO 9141, for control of the K-diagnosis line. The application works as a stand-alone test environment for development and service, and is also available for integration into complex test systems such as might be used for final production checking of control units. ...more

Serial RS422, RS423, RS232 analyzer tester and data line monitor with buffer capacity of 1 megabyte of memory. Line speeds to 230.4K (half duplex), 75-115,200 asynchronous, 75-64 kbps synchronous and bisynchronous, SDLC/HDLC, isochronous protocols. Supports MIL-Std-188-114 monitoring, testing and RS485 simulation. Small, lighweight and portabl ...more

The 6165 is a two-channel amplifier-filter module. Each channel has isolated input, 50 kHz bandwidth and two outputs that can be filtered or wideband. Bandwidth of 100 kHz is optional. The input is two-wire shielded and is isolated from the outputs, power and control interface. This gives the user complete freedom to ground the input without c ...more

The PR570 identifies and troubleshoots virtually any AC supply problem fast. Insure your safety and the safety of your test instruments whenever servicing electronic products. Conquer AC power source problems plus startup, shutdown, and regulator failures with a digitally accurate and variable 0-140 volt AC supply. ...more

The Series 90HV combines low-voltage solid-state technology with high-voltage relay technology ¾ solid-state devices for testing continuities and components at low voltage; relays for testing high-resistance isolation and high-current continuity. The high-resistance isolation tests are typically used to test the quality of harness insulation m ...more

Fully capable interface with room to grow in functionality and capability. Available an OEM unit; board only or in a small enclosure. RS-232 serial connection to host computer. Protocols supported; CAN, 2-wire (CAN-C or ISO 11898 or J1939); CAN, GM Single Wire CAN (SWC); J1850 VPW, GM Class 2, 1x and 4x modes, block transfers; CAN ISO 15765 support ...more

The AVT-718 Multiple Interface is a single unit solution for communicating with all of the most popular network protocols found in-use today or destined to be found in tomorrow’s vehicles. It is a complete solution, with no additional boards or modules to buy. The AVT-718 supports the following automotive network protocols: • CAN (2-wire and GM sin ...more

The model AVT-418 is an Ethernet Interface between a host PC and most of the automotive network protocols used by modules and vehicles now in production. The AVT-418 Interface supports all of these different automotive network protocols: • CAN; 2-wire (CAN-C or ISO 11898) - Ford Motor Company approved. • CAN; 2-wire (CAN-B or ISO 11519). • CAN; Si ...more

The IQS300 Series of Power Inverters provide 120 Volts AC or 220 Volts AC at 300 Watts of continuous power from a 12V, 24V or 32 Volt DC source. State of the Art MOSFET technology coupled with unique "Soft-Start" circuitry guarantees reliable operation. The ON-OFF switch illuminates when AC is present at the outputs to provide positi ...more

The AVT-716 Multiple Interface is a single unit solution for communicating with many of the network protocols found in-use today or destined to be found in tomorrow’s vehicles.The AVT-716 hardware revision “E” supports the following automotive network protocols: • J1850 VPW • Keyword Protocol 2000 (ISO 14230) • J1850 PWM • GM’s ALDL (8192 UART) • I ...more