High Voltage Switching

The HXV Series of switching products offers Matrix or multiplexer configurations for hot switching up to 3500 Volts and cold switching up to 5000 Volts. Two styles of switch modules may be configured into pre wired mainframes with a choice of control styles and LED display of all latched switch points. ...more

The 10-310/315 Range of High Voltage Switching Modules will Switch up to 1000V with Isolation to 1500V.Two module types are available:8 x Normally Open Relays and an 8 Channel Multiplexer, available with either Dry or Mercury Wetted Reed Switches. 10-310/315 high voltage switching modules are available in both SPST Relay or Multiplexer version ...more

This series of high voltage switching power supplies is designed to quickly charge capacitors and pulse forming networks in lasers and general modulators. Advanced semiconductor technology combined with high quality construction, yields an exceptionally small and reliable power supply which has set the industry standard for many years ...more

This series of high voltage switching power supplies is designed to quickly charge capacitors and pulse forming networks in lasers and general modulators. Advanced semiconductor technology combined with high quality construction, yields an exceptionally small and reliable power supply which has set the industry standard for many years ...more

Extremely rugged and reliable three-in-one tester. Vibrates when voltage is present. Tests for high voltage up to 600V AC/DC. Tests for low voltage as low as 5V AC/DC. Automatic switching continuity tester. ...more

Switching mode design High efficiency Pure sine wave output voltage 12 VDC input and 115 VAC output Overload protection High output current surge Low battery alarm / shut down Low idle power draw of less than 0.5 Amps ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc. ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc. ...more

For the generation of high voltage lightning and switching impulses according to IEC 60060 for indoor and outdoor use. Impulse voltage generator, charging and control unit, control and measuring system, chopping gaps  ...more

POWER SUPPLY TEST SYSTEM. The BRAT B509 is a double rack, stand-alone, high voltage, high power test system utilizing Commercial-Off-The-Shelf (COTS) equipment in a modular design. Its primary use is as Automatic Test Equipment (ATE) for power supplies with a wide range of input and output requirements. . ...more

The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system. ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc. ...more

The CKT1180-20 provides Users with high-voltage testing up to 3,500 VDC and 2,500 VAC RMS. The system is expandable to 6,000 test points in increments of 500 test points. Packaging of this system is an integrated unit comprising the control electronics, the stimuli generators and measurement instrumentation, plus the switching matrix. ...more

Power Supplies NGPX are high-performance programmable laboratory units (350 W) using linear regulation. With their excellent regulation characteristics these 19" units are ideal for use in development labs. Thanks to convenient manual operation and IEC/IEEE-bus control they can readily be integrated into production test systems. A rear tr ...more

Switching mode design High efficiency Pure sine wave output voltage 12 VDC input and 115 VAC output Overload protection High output current surge Low battery alarm / shut down Low idle power draw of less than 0.5 Amps ...more

HSA series is a power amplifier which has high speed, broad band (DC to max.10MHz) , and the capability of supplying high voltage and high power. DC+ / DC- signal is variable continuously with wide output range of maximum 300Vp-p without switching. Furthermore, as Four-quadrant output is possible, source mode(providing a power to load from a p ...more

TR518FR is one of the full series of products TRI released to satisfy the different @ environment requirements for different types of products. Its switching boards use an advanced but long lasting mechanical reed relay, suitable for analogue@products and high voltage and current testing, it also has the auto-alignment @ function. ...more

Power Supplies of High Voltage up to 2kV @ 0.5A and high current up to 100 A @ 10 V are available. Above 100 W power supplies have triac based pre regulator. Switching frequency above 100 KHz for SMPS.  ...more

The OhmstikPlus Live-Line Micro Ohmmeter measures the micro-ohm resistance of conductors, connectors, splices and switching devices positioned directly on an energized, high voltage lines. Measure microhm resistance on a live high voltage conductor ...more

The PS300 High Voltage Power Supply series consists of three efficient, microprocessor-controlled, switching DC power supplies capable of delivering 25 W of output power at voltages up to 5 kV. ...more

The PEL series are DC electronic loads which are ideal in aging ¡haracteristic analysis and product life testing applications including switching power supplies and batteries. A sophisticated program function enables high speed response and load characteristic simulation. A minimum operating voltage down to 0V is a standard feature of the V1 v ...more

Utilize PWM technology with switching amplifier design. 4 groups of digital LED displays - Frequency, Voltage, Current and Power or Power Factor. Programmable high/low limit settings on voltage, frequency, current, power and power factor.  ...more

The HB 50 Series offers a range of low cost high efficiency converters in the 25 to 50 Watt power range in an industry standard half-brick package. All models have a 2:1 input range including: 9-18VDC, 18-36VDC and 36-75VDC. Single output voltages of 2.5VDC to 24VDC cover the most popular applications. Isolation voltage is 1500VDC minimum. Swit ...more

3 memories. Able to store voltage, frequency and current high limit setting. Utilize PWM technology with switching amplifier design, the efficiency up to at least 80%. Compact in size and light weight. As small as 2U(8.9cm) height for capacity for 500~2000VA ...more