Showing results: 1 - 15 of 16 items found.
-
AF-DI-1000 -
Advanced Fiber Solutions
Our latest introduction to the DR500 series line is the ferrule end fiber scope which enables the technician to view the end surface of the ferrule with an enhanced image of the fiber core and cladding. With AF-DI-1000* scope attached to the DR500 series OTDR via the side USB port the technician is able to determine the quality of the surface of the ferrule. The fiber scope enables the technician to see scratches, scrapes, dirt or any residual that might be on the ferrules surface area. If desired the fiber end image can be saved and downloaded to the PC for further analysis.
-
0700-7950 -
KITCO Fiber Optics
KITCO Fiber Optics introduces our new 200X dual illumination inspection scope.
-
D SCOPE MT -
DATA-PIXEL SAS
The new D SCOPE MT microscope for MTP/MPO connectors is the fastest on the market. In the same measurement cycle, D Scope MT checks every optical fiber surface condition, and allows the operator to control the cleanliness of the connector endface and guideholes.
-
D SCOPE EFI – D SCOPE EFI-C – D SCOPE EFI-C LWD -
DATA-PIXEL SAS
The new D Scope EFI for MTP/MPO and multifibers field connectors is a cost effective microscope for inspecting fiber optic patchcords and cassettes.
-
AF-FMD-200 -
Advanced Fiber Solutions
AFS is please to announce the availability of the AF-FMD-200 mini hand held fiber microscope. The AF-FMD-200 is designed to inspect fiber termination ends, providing the most critical view of the fiber end face. This mini scope is smaller, lighter and easier to carry than a standard hand held scope. The AF-FMD-200 has two separate light modes, co-axial LED mode for direct viewing of the end face and oblique LED mode for angle viewing of the end face.
-
Evident Scientific
These external units provide illumination which is transmitted to the viewing instrument by a light guide cable, and then through the scope via the integral fiber bundle to the viewing tip.
-
D SCOPE -
DATA-PIXEL SAS
This unique microscope combines high quality optics with a modern and ergonomic design ideally suited to fiber optic applications. Until the D Scope, most microscopes were suffering from poor illumination quality yielding variable and non-reproducible image quality even amongst scopes of the same kind.
-
DRA5228/F -
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Um -
Nanometer Technologies
● Test 12 or 24 fiber MT Connectors● Find Endface defects fast● 800x Magnification●Numbered Dial Indicator to quickly identify which fiber you're onThe Um MT Inspection Scope accurately shows defects in your MT 12 or 24 fiber connectors. Quickly view each fiber to save time and money. Our unique Fiber Dial shows which fiber you are inspecting. No more getting lost!The Um MT is compatible with our Eagle Inspect Software. Create reports with images for your MT connectors.
-
Optical Wavelength Laboratories
A dependable connector endface inspection scope is a vital part of any fiber optic professional’s tool kit. Inspecting patch cord connector endfaces before attaching them to equipment or patch panels saves time and effort, and ensures a clean, quality connection. These 400x video inspection scopes allow users to view connector endfaces on a PC or laptop screen, preventing harmful invisible light from entering the users eye, and ensuring maximum eye protection.
-
D SCOPE MT LWD -
DATA-PIXEL SAS
Designed for inspection of MPO connectors, patch-cords or bulkheads, the D Scope MT LWD checks the cleanliness of the connector face and precisely measures the defects on the optical fiber end-faces. Using Deep Learning technology associated with a high-resolution optical bench, the scratch and defect detection thresholds are significantly improved compared to traditional software.
-
Titan Tool Supply, Inc.
The "P" Series Flexible Borescope is a small diameter scope without articulation that will fit into a .128" hole. It is 36" overall length. The basic borescope is .120" (3mm) in diameter with a Tungsten braid mesh sheathing for better durability. The unit has a 1.5" minimum bending radius. It is constructed of 10,000 individual fibers with a 25X eyepiece to magnify the image received.
-
OptiConcepts
The USB Connector Inspection System features easy focusing with high resolution imaging. The system includes standard software that provides image display, image capture, digital zoom, auto calibration, and basic analysis tools. Pass/Fail analysis and reporting features are optional software features. The Inspection System scope is fully compatible with the FiberWarrior Pro OTDR as well as other FiberWarrior Pro test sets, providing a full fiber optic testing solution.
-
Bobcat -
Fiber Instruments Sales Inc.
The Hand Held Bobcat OTDR has a generous 32 dB dynamic range and a short dead zone for testing FTTx fibers and networks up to the metro environment. It has an easy to read color display with fault finder, construction and expert/manual modes of operation. The OVP is shipped with Windows®/Telcordia SR-4731 compatible software that generates complete and professional documentation with the ability to include scope images and loss test results on the OTDR test reports.
-
ZT-03(400X) ZT-03(200X) -
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
*Fast and convenience, accurate and high efficiency , the image is very clear and bright .save time and reduce cost.*The lens’axis of XY can adjust. the scope is : X axis direction is 4mm, Y axis direction is 3.5mm,it can check.*Optical magnification: 200X, 400X 500X* Long sevice life. Inner LED service life can up to 100000 hours,* Absolute laser safety. built in CCD CAMERA(not the human eye) view the optical fiber’s terminal face. Even check the terminal face of the optical fiber during the laser transmission. Without any safety problem.