Electrical Safety Test

This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also u ...more

The 601 Pro SeriesXL is an automated electrical-safety analyzer that meets stringent international standards for electrical-safety testing of hospital and laboratory electromedical equipment. The 601 Pro SeriesXL is also available with a built-in printer. ...more

The 180 Electrical Safety Analyzer is a lightweight and ultra-portable test device for ECG-device-leakage and isolation testing. ...more

The ESA601 Electrical Safety Analyzer is a full-featured, compact and portable manual tester that allows you to test to multiple country-specific standards. ...more

The model 307A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

The model 308A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

Checks voltage from 100V to 600V AC/DC. Convenient pocket-sized tool provides maximum safety when pulling cartridge fuses and checking electrical connections. Test prods fit parallel and tandem slot receptacles. Built-in resistors limit current flow to eliminate false indication. For 9/16 inch to 1 inch fuses, 100A/250V and 60A/600V. ...more

SIRIUS 87 is a model to performing all safety tests according to VDE 0413 on electrical installations. Inside model are integrated new fundamental features: the possibility to perform Loop Impedance (P-P, P-N, P-PE) at high resolution (0.1mOhms) with use of IMP57 optional accessory. Thanks to its PC interface and powerful software you will cre ...more

The Elite test system is Clare?s flagship product and features 11 powerful tests in one tester.  These tests are: AC/DC flash/hipot, DC insulation resistance, earth/ground bond and leakage.  The Elite is designed for automatic dual voltage (230V/115V, 50/60Hz) operation and is capable of testing product safety in accordance with most interna ...more

Dielectric Strength Testers in the DMG series perform dielectric strength testing and insulation measurement enabling the guarantee of good quality insulation materials and the conformity of electrical appliances to the safety standards. ...more

A versatile portable test set providing simple straightforward operation and effective electrical safety testing of office equipment, power tools and appliances.  ...more

The Rigel 277 Plus is a portable medical electrical safety analyser combining IEC/EN 60601-1 compliance with additional test facilities for IEC/EN 61010 (Laboratory Equipment) including Touch Leakage, Voltage Measurement and dedicated IEC 61010 Measuring Device (Body Model). ...more

The 1650 Series testers verify the safety of electrical installations in domestic, commercial and industrial applications. They can ensure that fixed wiring is safe and correctly installed to meet the requirements of IEC 60364, HD 384 and all relevant local standards. ...more

The AC-TESTER is a compact universal test unit designed for testing electrical insulation and electrical safety of electronic equipment and electrical systems. High-voltage test of electrical insulations up to 5 kV, 100 mA. Measurement of protective earth resistance with test current 25 A. Measurement of insulation resistance with 500 V ...more

GSC53N is a strong evolution equipment developed by HT ITALIA to perform complete test and verify on electrical installations according to the most common safety standards (IEC 61557, VDE 0100, BS7671) and for power quality analysis on general electric networks. ...more

COMBITEST2019 meter can performing necessary safety tests on electrical plants according to VDE0413. Measurement of Continuity, Insulation, Global Earth values without RCD's tripping, RCDs test, Line and Fault Loop Impedance measurement (also at high resolution 0.1mOhm with IMP57 optional accessory) with prospective short circuit current calcul ...more

Ross Engineering Corporation's High Voltage Megmeter is a unique battery powered HVDC source and meter. Models are available for withstand testing of insulation up to 42KV DC, as well as measuring leakage current as low as 0.001 microamp and resistance as high as 30 million megohms when testing underground cable, rubber safety gloves, vacuum in ...more

With reference to ASTA, BSI and other regulatory body requirements, it has become standard practice supply mains powered electricals products with pre-wired cord sets fitted with either moulded-on or re-wireable connectors. In response to cord set manufacturer requirements, for a production line tester to ensure 100% build integrity and electri ...more

COMBI420 is an innovative meter designed to perform all safety test verifies on electrical installations in compliance to recently standards (VDE0100, BS7671 and so on, measure and save results of environmental parameters (illuminanance, temperature, sound level), leakage currents and active power, harmonics, power factor measurements on single ...more

Recognised as the industry standard and product of choice for the Hire and Service/Repair industries. Simple straightforward operation, compact size and a comprehensive range of measurement functions, make this tester the leader in its class. Testing with the B255 will ensure compliance with European and International standards for Class I and ...more

The new SafeCheck 8 tester has been designed specifically to ensure that traceable test results can be stored for rental products when PAT tested between hires.  These traceable test results will clearly demonstrate that a rental product supplied into the DIY or construction industry is electrically safe and functions correctly, at the time o ...more

MAXTEST HT2038 is a highly professional portable multifunction meter designed for safety test on each kind of electrical installations, in compliance to VDE0413. It is distinguished by a large choice of measuring functions. It contains approx. 1000 memory locations for storage of test results that can later be transferred to PC via RS-232 and a ...more

The Rigel 266 Plus is a highly compact, easy-to-use medical electrical safety analyser, designed to test in accordance with IEC/EN 60601-1, MDA DB9801, and AS/NZ 3200. ...more

FULLTEST4050 model was designed to performing all necessary tests in industrial environments on electrical machines, devices and type-tested assemblies (TTA) or partially type-tested assemblies (PTTA) in compliance with EN60204-1 and EN60439-1 respectively. Adding this, the meter is complying with partial tests according to EN60601-1 (medical e ...more

The high-voltage DC test set, PG 5-501, was designed for testing electrical components and circuits with high dc voltages. It is used for quality control and production line testing. The unit mainly consists of a safety test cover and a high-voltage generator integrated. ...more