ETSI - aka European Telecommunications Standards Institute
|Sponsor Your Catalog|
VB12 - Rugged 10 TV Streams ETSI Monitor / Analyzer The ability to monitor 10 streams (upgradeable to 50) with full ETSI TR 101 290 analysis and alarming makes the portable VB12 invaluable for field use. Its ruggedised exterior and fan-less design give engineers the perfect fault-finding tool when roaming in the network or for permanent placement of a unit in harsh environments.
V5.x - Protocol Analysis GL's V5.x Analyzer is used to view and analyze the V5.X protocol between an Access Network (AN) and a Local Exchange (LE) which operates only on E1 circuits. Using the real-time mode of operation, the V5.x Analyzer can be used to capture and analyze a stream of frames from the link between the LE and the AN. The user can select the ETSI or ITU-T standard from the main menu of the V5.x Analyzer GUI to view the decode according to the corresponding standard.
Media Gateway Control (MeGaCo) - Emulator using MAPS GL's Message Automation & Protocol Simulation (MAPS™-Megaco) is an advanced protocol simulator/tester designed for Megaco testing, which can simulate MGC to test Media Gateways with various types of calls. It can also control scenario involved in Media conversion. The MAPS™ - MEGACO test tool is designed with 200+ test cases, as per Megaco specification of ETSI TS 102 374-2 document. Test suite includes in-built scripts which tests the functionality of the Media Gateway for Megaco protocol valid and in-valid behavior.
ISDN - Protocol Analysis GL's ISDN analyzer can capture and analyze stream of frames on an ISDN PRI link. It decodes LAPD according to Q.921, while, the ISDN information parsing is done based on the user's selection of ITU Q.931, AT&T/Lucent switch 4ESS and 5ESS (TR41449, TR41459 and 235-900-342), Nortel's switch DMS-100 and DMS-250 (NIS-A2111-1 and NIS-A211-4), Bellcore National ISDN-2 (NI-2), Euro ISDN (ETS-300 102-1), QSIG ETSI, ANSI T1.607, DPNSS, DASS2, and ARINC 746.
Move 2 - ISO, SWP/HCI, IC-USB Spy Tool Tracing communication between a terminal and a Smart Card according to ISO/IEC 7816 1-4, SWP according to ETSI TS 102 613, HCI according to ETSI TS 102 622, USB according to ETSI TS 102 600
TTsuite-ITS The TTCN-3 test suite for running conformance tests against ITS equipment: Transmission of IP packets over GeoNetworking - ETSI TS 102 859-x V1.2.1 (2014-04), Co-operative Awareness Messages (CAM) - ETSI TS 102 868-x V1.2.1 (2014-04), Decentralized Environmental Notification Messages (DENM) - ETSI TS 102 869-x V1.2.2 (2014-04), GeoNetworking Basic Transport Protocol (BTP) - ETSI TS 102 870-x V1.1.1 (2011-03), GeoNetworking ITS-G5 - ETSI TS 102 871-x V1.2.1 (2014-04).
SWP/HCI UICC Test Suites The Collis SWP UICC Test Suite and Collis HCI UICC Test Suite are the ideal solution to test the compliance a UICC on the most recent ETSI specifications.
GEM-V5TTCN - Protocol Tester The GEM-V5TTCN is a protocol tester for ensuring Local Exchange (LE) and Access Network (AN) conformance to the ETSI V5 series of documents. Equipment manufacturers can use GEM-V5TTCN to demonstrate conformance against the ETSI V5 specifications. Telecom service providers can use GEM-V5TTCN to prove out vendor equipment prior to deployment in their network.
TTCN - Testing and Test Control Notation TTCN(Testing and Test Control Notation) is a standardized testing language and test system architecture defined jointly by the ETSI and ITU standards organizations. Compliant with ISO/IEC 9646 (Testing Methodology and Framework) as well as ISO/IEC 9001 (Quality Management).
V5 L3 - Signaling Tester The V5 L3 Signaling Tester is a test environment for the V5 L3 signaling specification as defined by the ETSI standards. It is a SAFIRE based test harness able to run pre-defined ACATS test scenarios against V5 L3 test objects in a controlled & deterministic manner.
V5 - Signaling Tester The V5 L2 Signaling Tester is a test environment for the V5 L2 signaling specification as defined by the ETSI standards. It is a SAFIRE based test harness able to run pre-defined ACATS test scenarios against V5 L2 test objects in a controlled & deterministic manner.
Diameter Signaling Tester The Diameter Signaling Tester is a test environment for the Diameter signaling specification as defined by the ETSI & IETF standards. It is a SAFIRE based test harness able to run pre-defined ACATS test scenarios against Diameter test objects in a controlled & deterministic manner.
GSM A - Signaling Tester The GSM A Signaling Tester is a test environment for the BSSAP and Interface Layer 3 signaling specification as defined by the ETSI standards. It is a SAFIRE based test harness able to run pre-defined ACATS test scenarios against BSC or MSC test objects in a controlled & deterministic manner.
IT³ Prove! - Smart Card Terminal Simulator Digital simulation of Smart Cards according to ISO/IEC 7816-4. Terminal testing as specified by ETSI or 3GPP by making use of simulation modules for (U)SIM, (U)SAT, CCAT, ISIM and CDMA2000. Test suites for GSM, 3G, CDMA2000.
SIP - Conformance Analyzer SIP Conformance Analyzer is an advanced testing solution for SIP enabled products widely used in today's VoIP and 3G networks. Comprehensive tests, protocol simulation and analysis tools verify SIP compliance according to ETSI TS 102 027 / RFC 3261 ensuring high probability of interoperability.
2310 - Signal Analyzer Setting new standards in TETRA transmitter analysis where speed and accuracy counts. # Accurate TETRA transmitter measurements # Test TETRA base stations, terminals and direct mode radios # All measurements made in accordance with ETSI EN 300 394-1
IN - Intelligent Networks Protocol Analyzer The Intelligent Networks Protocol Analyzer is a SAFIRE Tracer Plug-In for decoding Intelligent Networks signaling according to the protocol specifications provided by ITU-T, ETSI, ANSI, national and proprietary standards.
ESA 10 - SIGNALING ANALYSER Dual 2048 kbit/s interface with high impedance capability ■ Interface meets to ITU-T Rec.G.703 / G.704 / G.706 / I.431 / and ETSI ETS 300 011 ■ External clock input
EMC32 - EMC Measurement Software EMC Measurement Software. Support of measurements to civil standards such as CISPR, IEC, ISO, EN, ETSI, VDE, FCC and ANSI. Manual and automatic EMI and EMS measurements. Can be combined with EMC test systems and EMI test receivers/analyzers from Rohde&Schwarz.
H.323 - Signaling Tester The H.323 Signaling Tester is a test environment for the H.323 signaling specification as defined by the ETSI standards. It is a SAFIRE based test harness able to run pre-defined ACATS test scenarios against H.323 test objects in a controlled & deterministic manner.
IPTV Metadata Server - Generation and delivery of SD&S and BCG metadata IRT's IPTV Metadata Server provides all necessary metadata information to run IPTV services compatible to the DVB-IP standard (ETSI-TS 102034 v.1.3.1), or to another IPTV specification based on aforementioned standard (e.g. Open IPTV Forum). It delivers all required Service Discovery and Selection (SD&S) records and EPG data for Broadcast Content Guides (BCG, ETSI-TS 102539 v.1.1.1) via both delivery mechanisms, http and multicast. The IPTV Metadata Server is ideally suited to integrate with IRT's Broadcast Server to provide a IPTV server system for both video and audio streaming with metadata support.
Clarinet-TTCN ISDN France-VN4 ETS * Protocol: ITU-T Q931 and ETSI standards, France-Telecom VN4 specifications ("Règles Techniques Particulières" ) define protocol for ISDN Equipment
* IUT: ISDN BRI User Equipment for Network Layer
* ATS: F4XUB - ACACIA has signed the ATS use agreement with FT (CNET license n°1165)
3000 Series - Remote Cabinet and CO Splitters Comtest’s 3000 Series splitters are designed specifically for the European market. Their all-front connectors allow them to slot conveniently into ETSI racks at CO or a remote location—without the need for swing shelves. Cards are available for both POTS and ISDN and are compliant with ADSL2+ and VDSL technology.
SM-A-FD - TAMs The in-line modular TAMs are designed to plug straight into the DSLAM, but due the DSLAM construction this is not possible as the module extends outside the cabinet. When space is available within the DSLAM rack an Internal Shelf is utilised to house the FD modules. Should there be no space available, the shelf will fit in a standard ETSI rack. The Modules are inserted in the shelf.
Results 1 - 24 of 50
ETSI - European Telecommunications Standards Institute.
- Analysis (7)
- Analyzers (12)
- Cards (5)
- Control (2)
- EMI Receivers (2)
- Ethernet Switches (2)
- Harness Testers (9)
- Interfaces (6)
- Modules (7)
- Network Analyzers (4)
- Protocol Analyzers (4)
- Services (4)
- Signaling Testers (10)
- Simulators (4)
- Software (4)
- Switches (3)
- Test Harness (9)
- Test Systems (3)
- Testers (16)
- Testing (11)
- »See all 68 Categories