|Sponsor Your Catalog|
EMC / RF Test System Engineering / Development & Integration Anechoic chamber, radio isolation room construction, removal, maintenance and repair. System Integration of complete Test System. Development team has the expertise and technical experience and provide a customized service demand, the project includes a full range of EMI / EMS / RF test equipment with neighboring sell and repair
NSG 4070 - EMC Immunity Test System An advanced combination of signal generator and compact immunity test system. Its large frequency range from 9kHz to 1GHz and its modular set-up using internal or external amplifiers enable a large variety of applications including tests according to IEC 61000-4-6, various BCI applications as well as signal generator and power meter for test systemsas per IEC 61000-4-3, IEC 61000-4-20, IEC 61000-4-21 and many other applications.
EMC Testing Reduce interference potential by knowing your electromagnetic environment. Radio frequency measurements of potential interference at your installation can help reduce problems in sensitive installations. To make these determinations, very specific measurements must be taken on location. And you probably needed it done yesterday.
EMI/EMC Testing This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements. During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
EM Series - EMC Lab Low Loss Armored Test Cables MegaPhase's EM series is a test cable specifically for the needs of EMC lab technicians. These cables feature exceptionally low insertion loss, excellent RF shielding properties and crush resistant armoring.
Preamplifiers - EMI/EMC testing from 100Hz - 40GHz Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured.
EMC ANTENNAS - TESTING UP TO 40 GHz Com-Power EMI / EMC broadband and tuned antennas cover the frequency range of 9 kHz - 40 GHz for EMI/EMCTesting. They can be used for both radiated emission and immunity testing (antenna used as a transmitter to generate electromagnetic field).
LISNs - Conducted EMI / EMC emissions testing Com-Power Line Impedance Stabilization Networks (LISN) are intended for electromagnetic interference (EMI) testing and certification of electronic products at an EMC test laboratory. The LISN were designed and built to match the impedance characteristics given by the individual test specification.
Antennas for EMC testing * Conventional log periodic types for OATS applications. * Miniature antennas for chamber and small enclosure applications. * Large loop antenna for EN55015 compliance testing.
GF303D-R - EMC Test Power Source GF303D is designed as the special EMC laboratory for the special requirements, and its output by electromagnetic compatible equipment decoupling network can be used as the electromagnetic compatibility of the input of the inspection equipment. It is suitable for power system of electrical measurement, thermal, remote, scheduling and so on need measurement, inspection and high precision standard source power department and the enterprise, especially suitable for metrology institute, electric power academy of sciences as EMC experiment to test equipment to provide standard input. Electromagnetic compatibility test power source is the use of advanced technology and special process design, product anti-interference ability, suitable for attenuation oscillating magnetic field, attenuation oscillation wave, fast transient pulse group, surge and electromagnetic compatibility project immunity test, electromagnetic compatibility test instrument is the necessary equipment. The product has good stability, high degree of automation, use agile and convenient, easy to carry, etc.
GF303D can be used as the standard source in the electromagnetic compatibility lab, also used to test doing EMC experiment inspected meter’s accuracy. But it can be used with some equipment work together in the electromagnetic compatibility lab: for example surge generator; Group of pulse generator; Frequency drop generator; Electrostatic generator etc.
TestLab Suite - EMC testing software TDK TestLab supports full automation for a variety of EMI and EMS tests specified in North American, European, and Asian regulations. This allows you to create a fully automated system that practically runs itself.
CGC SERIES - COMB GENERATORS FOR CONDUCTED EMI / EMC TESTING The same principle that is used for verifying radiated emissions test site, can be employed to test the conducted emissions setup in an EMC test laboratory with a CGC series Comb Generator.
PSE-GB. - K0 ACTUATOR for EMC tests Pneumatically operated actuator for operation of accelerator and brake pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box. Fast, simple and robust installation on vehicle driver seat.
EMC&EMI test equipments ESD test equipment (intelligent static-electricity discharge generator) 1) Meet standard: IEC61000-4-2 and GB/T17626.2 2) LCD display, smart-control high voltage output, in-built standard class parameters, small and light to be convenient for operation. 3) Easy to operate, with software protection
EMC-MC - Mini Compact EMC Test Chamber Very useful where space is restricted, the EMC-MC will settle into almost any office space. Its small overall size results from the use of our modular SmartShield chamber lined with our AEPH HyPyr-LossTM absorber technology requiring less volumetric space than in a traditional chamber. This mini compact chamber is applicable in pre-compliant EMC and general Research & Development RF testing.
GTEM - Test Cells for EMC Testing DC to 20GHz Emission and immunity testing in one fixed, shielded environment. Meets IEC / EN 61000-4-20 and FCC ANSI C63.4. Generated fields are largely homogeneous and simple to calculate. Efficient power conversion requires smaller power amplifier
PSE-GK - .K0 ACTUATOR for EMC tests Pneumatically operated actuator for operation of accelerator and clutch pedal in vehicles. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box. Fast, simple and robust installation on vehicle driver seat.
EMC500 - EMC Test System The EMC500 is the update instrument of EMC300A, Measure Range from 9kHZ~300mHZ. The basic functions and principles of EMC500 are based on EMC300A.
EMC Testing Compliance Testing Services. Exporting a product globally demands a properly accredited EMC laboratory to bring international recognition to your test results and compliance marks .
TTX-Optical Link –EMC Testing of FlexRay ECUs The TTX-Optical Link is a device to convert FlexRay signals to optical (fiber cable) and vice versa. It enables optical transmission of dual channel FlexRay signals for EMC testing while ensuring minimum influence on the FlexRay signals timing. With its shielded housing and built-in accumulator it fulfills all the requirements for EMC testing of a FlexRay network.
EMC tests EMI tests and EMC tests, as well as comprehensive design support of circuit cards, modules, equipment, subsystems, systems, and facilities are available though our partnership with Northrop Grumman. Tests are done in the laboratory or in the field. Our test facility in Sacramento (McClellan), California is conveniently located near the Silicon Valley. Electromagnetic surveys of a system or an entire facility can also be done at customer facilities. Name virtually any requirement for electromagnetic interference and electromagnetic compatibility and we can meet it - with reliable results.
EMC Engineering - EMC test lab EMC tests, CE-conformity tests, Testing during development, EMC consultancy service, Solution proposals for interference suppression.
EMC Testing Services F2 Labs can work with you during each phase of your design development – from your prototype phase compliance consulting to final product compliance testing and global approval management. Our technical staff can work with you at your location for EMC testing and approval management or test your product at our facilities. Feel free to witness your testing at our modern EMC facility. We are available to provide you with one or all of the following EMC compliance testing services:
PSE-GBK. - K0 ACTUATOR for EMC tests Pneumatically operated actuator for operation of accelerator, brake and clutch pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box. Fast, simple and robust installation on vehicle driver seat.
Results 1 - 24 of 231
EMC Test - Test determines noise immunity or electromagnetic compatability.
- Amplifiers (53)
- Antennas (26)
- Chambers (27)
- Control (39)
- Diagnostics (34)
- EW Simulators (33)
- High-Power Amplifiers (37)
- Instrumentation Amplifiers (34)
- Instruments (43)
- Laboratories (35)
- Loads (18)
- Mains Tester (18)
- Monitoring (35)
- Radar Simulators (33)
- RF Amplifiers (39)
- Services (17)
- Systems (23)
- Test Systems (24)
- Testers (21)
- Testing (133)
- »See all 217 Categories
- Component (45)
- Electromagnetic (38)
- Electronic Warfare (36)
- EMI (42)
- Frequency (40)
- GHz (64)
- IEEE (33)
- Immunity (34)
- Maintenance (49)
- Medical (35)
- Military (46)
- Power (33)
- Radar (35)
- Radar Test (35)
- Reliability (33)
- RF (72)
- Simulation (39)
- Simulation Testing (33)
- Standards (53)
- Troubleshooting (32)
- »See All 286 Features