-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
-
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Impact Series Power Discrete Semiconductor Tester
-
The Impact Series Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
-
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Gearbox Tester
-
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Hoist Tester
-
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
-
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Bit Error Rate Tester - MATRIQ
-
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
-
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Universal A/V Tester
-
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
The Lorlin© Impact Series
-
Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability. The system tests most all discrete semiconductors with reliable, accurate, and repeatable results.
-
Product
AXIe M8000 Series of BER Testers
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
-
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
MTM-Bus Tester
PXIe-1149.5
-
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
-
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
Automotive Power Discretes
-
ST offers a wide portfolio of automotive grade power discrete devices for reliable, robust and power-efficient automotive applications.
-
Product
Automated Discrete Semiconductor Tester (ATE)
5300HX
-
The Model 5300HX Automated Discrete Semiconductor Tester (ATE) is designed for fast, reliable testing of a wide range of discrete devices. Using an on-board Intel SBC, can provide stand alone testing capability or connected to a PC for intuitive test development and data capture.
-
Product
Discrete & Power Modules
-
A product portfolio that offers full spectrum of high, medium and low voltage power discrete devices along with advanced power module solutions, including IGBT, MOSFET, SiC, Si/SiC Hybrid, Diode, SiC Diode, and Intelligent Power Modules (IPMs).
-
Product
120 GBd High-performance BERT
M8050A
-
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Receiver, G18, 18 Module For Discrete Wiring
310120101
-
The lightweight and rugged 18 module Receiver provides a solution that will accommodate larger ATE chassis’ (PXI, VXI, SCXI). It allows immense versatility by affording space for up to an 18 slot PXI chassis.
-
Product
68-Pin SCSI Micro-D Female Discrete Wire
40-962-068-F
-
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
-
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
Product
Signal, Module, ID, CASS, 210 Position, Discrete Wiring
510114106
-
Module, ID, Cass, Signal, 210 Positions, Discrete Wiring
-
Product
16-CH Discrete Input 16-CH Discrete Output Module with UJ Type Connector
HSL-DI16DO16-UJ
-
*16-CH digital input and 16-CH digital output*Higher output current up to 90mA/channel*Isolation Voltage: 2500Vrms*JAE 3-pin connector*Easy installation and wiring
-
Product
Module Retainer Block Set, For Discrete Wiring, 2 Positions
510109117
-
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules hinge down with the receiver to provide easy access to wiring.
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, ITA
410112582
-
When storing the ITA, the cover snaps on to protect the modules and contacts. The body of the cover is clear chromated aluminum and the mounting blocks are made of Delrin.
-
Product
Battery Capacity Testers|Discharge Testers
-
DV Power offers a wide range of battery capacity testers to meet specific customer needs. All of them are portable, powerful and most of all universal. Any battery string, such as lead-acid, lithium-ion, nickel-cadmium based and others, with voltages in the range of 0,9 – 800 V DC can be tested in an accurate, user-friendly way.The capacity test is carried out following the battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU battery testers enable setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, several units can be connected in parallel, or BXL additional load units can be used. Discharge parameters can be monitored in real-time during the capacity test. Overall battery voltage, current, elapsed test time and capacity will be presented during the entire test on a touch screen display.
-
Product
Multi-purpose Tester
DEL-101
-
Standard Electric Works Co., Ltd
Mains wiring polarity check. ELCB/RCD testing. Measuring ear for line current. Measuring ear for leakage current. Helps calculate insulation resistance. Helps calculate power consumption. Helps fault finding of standing earth fault. Fused main adapter. Appliance testing (with the aid of a clamp meter). Fused appliance socket. No batteries required. HRC fuse inside. Fused, color-coded universal test sockets. Universal mains IEC Lead.
