Diagnostics

Sponsor Your Catalog
  • TruckController - Diagnostics unit for the J1939 CAN bus of trucks ruckController is a diagnosis unit for truck and body manufacturers at the body builder CAN interface respectively FMS interface of trucks. It supports all prevalent messages according to SAEJ1939 standard.
    B-plus GmbH
  • PCAN-Diag 2 - Handheld CAN Bus Diagnostics Unit PCAN-Diag 2 is a handheld diagnostics unit with a wide range of functions to allow investigation of a CAN bus, such as detection of the CAN bit rate, bus load measurement, and termination measurement.
    PEAK-System Technik
  • APCI-1500 - Digital I/O Board, 32 Isolated I/O Channels, 24 V. PCI interface to the 32-bit data bus. Connector compatible to PA 1500. Connector and software compatible to CPCI-1500. 16 isolated input channels, 24 V, including 14 interruptible. 3 software-programmable counters/ timers. 16 isolated output channels, 10 to 36 V, output current 500 mA. Timer-programmable watchdog for the reset of the outputs to ?? Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog. Interrupt triggered through watchdog, timer, error. One ground line for all inputs and one ground line for all outputs.
    Team Solutions
  • P.H.D. MiniPCI - Advanced Diagnostics Board P.H.D. MiniPCI is an advanced diagnostics board that can be used by service technicians, system integrators & developers to perform sophisticated diagnostic testing on MiniPCI bus systems with Intel compatible processors. 
    Ultra-X
  • P.H.D. PCI2 - Hardware Diagnostic Tool P.H.D. PCI2 is an advanced diagnostic card that is used by service technicians and engineers to perform sophisticated testing on PCI bus systems with Intel Pentium III and newer processors (AMD & VIA processors also supported).
    Ultra-X
  • VDIS-2 - VME Display and Diagnostic Module VDIS-2 is the new, improved test and diagnostic module for VME-bus systems. It is equipped with LED's for all VME bus lines but also allows to trigger on error conditions, generate DTACK's and be adressed for read and wite VME calls.
    Hartmann Elektronik
  • Vehicle Spy Professional - Tool to Perform Diagnostics, Data Acquisition and Testing Vehicle Spy Professional is a single tool that enables you to perform diagnostics, node/ECU Simulation, data acquisition, automated testing, memory edit or calibration, and vehicle network bus monitoring. The design of Vehicle Spy is focused on one thing, your productivity. This means the tool is designed for ease-of-use and a low learning curve. With the exception of customer specific features, all the functionality available in Vehicle Spy is offered at a single low price.
    Intrepid Control
  • samDia K- - Line-Module Simulator The K-Line Module Simulator allows the simulation (remaining bus simulation) of the diagnostic interface of motor vehicle control units for test and demonstration purposes. This allows e.g. a very convenient debugging of diagnostic software in the tester. The available automation interface enables the presentation of complex simulation scenarios with the help of the HS+ Interface
    Samtec Automotive
  • DATAIR-400 - Handheld ARINC 429 Data Monitor The DATAIR-400 Handheld ARINC 429 Data Monitor is an easy to use diagnostic tool. It connects to an ARINC 429 data bus for instantaneous display of the active Labels on the bus - without any preset conditions.
    YED Ltd
  • HUD - Vehicle-Mounted Head Up System Automatically adapt to the automobile models with OBD II (Bus Automatic Diagnostic System) interface. Display the engine speed, speed, voltage, temperature, tire pressure, fuel consumption and other information on the front windshield of the driver's eye level.
    AutoDiag Technology
  • FTLF1322P1xTR - OC-12 IR-1/STM S-4.1 RoHS Compliant SFP Finisar's FTLF1322P1xTR SFP transceivers are compatible with the Small Form Factor Pluggable MSA. They comply with SONET and SDH standards. Digital diagnostics functions are available via the 2-wire serial bus.
    Finisar
  • FTLF1323P1xTR - OC-3 IR-1/STM S-1.1 RoHS Compliant SFP The FTLF1323P1xTR SFP transceivers are compatible with the small form factor pluggable MSA. They comply with SONET and SDH standards, and are suitable for fast ethernet applications. Digital diagnostics functions are available via the 2-wire serial bus.
    Finisar
  • ST-6000 - Auto Diagnostic Scan Tool ST-6000 is an advanced Scan Tool whose sophisticated technology allows to effect in a very simple way the serial diagnosis of all the electronic systems (CAN bus included) installed in vehicles and motorcycles.
    Brain Bee S.p.A.
  • moduleanalyser - Flexible Network Analyser and Automotive Diagnostics Module Analyser is a 5 in 1 easy to use CAN bus analyser with the following advantages Automotive OBD Scan tool and J1939 Automotive UDS - (supports ISO14229, ISO15765) ODX editor CAN BUS monitoring Data Acquisition
    Influx Technology
  • CCX500 - OP-COM OP-COM is a PC based diagnostic program. It covers almost all Opel cars, even new cars with CAN-BUS based diagnostic, such as Vectra-C, Astra-H, Zafira-B. The program lets you to read out and clear fault codes, shows you live data, lets you to perform output test, and supports remote, and key programming. The program supports many control units, like Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, Body Control Unit, just to name a few examples.
    China Century Technology
  • ST8677 - PC motherboard diagnostic post debug test card for laptop and desktop LCD displays shows diagnosis result of motherboard. Especially helpful to pinpoint where is the problem when power on the computer and find no display or machine hang. PCI bus reset and CLK signal working indicator.(When indicator LED is on to indicate its respective signal is fine.)

    Compatible with Phoenix, Award and AMI Bios motherboards which has the PCI bus slot ,mini pci,mini pci-e or LPC port .

    Intelligent analysis of the code corresponding to the cause of the malfunction, and gives diagnostic program!
    Shenzhen Sintech
  • PMC-8670 - PMC CPU Board Diagnostic Module # Standard: IEEE P1386.1 # Form Factor: Single size PMC, 74.0 x 149.0mm (W x D) # PCI Bus: 32-bit/33MHz # V (I/O): 3.3V or 5V # Diagnostic: Port80 display for CPU board power-on-self-test (POST) status; LED indications for system DC voltages (5V, 3.3V, 12V, -12V); PCI bus activity indication
    ADLINK Technology
  • onTAP ProScan - Boundary Scan (JTAG) Test Software onTAP provides comprehensive boundary-scan test development tools with powerful run time software including pin-level diagnostics. onTAP provides everything required for robust JTAG test solutions. Robust ATPG for high fault coverage and precise pin-level diagnostics. Interconnect, Bus Wire, Pull-up/Pull-down, TAP Infrastructure tests, Shorts and Opens. Memory/Cluster tests employ Virtual Pins to test non-JTAG memory and FLASH devices.
    Flynn Systems
  • basicCAR 3085 - Mini network tester The mini network tester basicCAR 3085 is a stand-alone solution for testing important test complexes, such as net management, diagnostic or data determination or node configuration via CAN and LIN. The modular solution provides up to two CAN interfaces, two serial interfaces (configurable as K-Line or LIN interface), an interface for the J1850 communication protocol, integrated clamp control (Kl.30, Kl.15) as well as disturbance functions for CAN and LIN. Transport protocols, diagnostic and various intelligent additional options (all executed on-board) are available in analogue form to the CAN bus controller PXI/PCI 3052 and basicCAN or the LIN bus controller PXI/PCI 3072 and basicLIN.
    GOEPEL Electronic
  • ST8679 - PCI+Mini PCI-E+mini PCI+LPC port PC diagnostic test debug port card LCD displays shows diagnosis result of motherboard. Especially helpful to pinpoint where is the problem when power on the computer and find no display or machine hang. PCI bus reset and CLK signal working indicator.(When indicator LED is on to indicate its respective signal is fine.) Compatible with Phoenix, Award and AMI Bios motherboards which has the PCI bus slot ,mini pci,mini pci-e or LPC port . Intelligent analysis of the code corresponding to the cause of the malfunction, and gives diagnostic program! It can display the halting execution automatic with a couple of times.
    Shenzhen Sintech
  • PP619 - CAN Test Box The CAN Test Box gives you easy access to the 16 pins of the diagnostic connector that is fitted to all modern vehicles. Depending on the configuration of the vehicle, this may allow you to check power, ground and CAN Bus signal quality. With the test leads supplied you can connect your PicoScope automotive scope, or any other suitable scope, to the CAN breakout box to monitor any signals present, such as the CAN High and Low signals.
    Pico Technology Ltd
  • ESN2000/ESN2010 - EScan Pro Diagnostic Scan Tool PC Based Drivability Tool with Sharp SHOOTER™ Technology • Connects to ISO-9141-2, KWP2000, J1850 (PWM and VPM), and CAN Bus Types • Very Fast Auto Connect • Easy PID Setup plus Calculated PIDs • Digital and Slide Bar Readouts • Powerful Graphing • Cursor Measurements of Charted or Recorded Data • Recording of Data and Screen Shots • Reads and Plots Monitors • Reads and Decodes DTCs and Pending Codes
    Automotive Test Solutions
  • FTEN2117P1NUN - SFP transceiver Finisar's EPON Sticks are combination of a SFP transceiver with a built-in EPON ONU. They comply with IEEE802.3ah EPON standard and optionally, CTC OAM specifications, and DPoE™ specifications. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA.
    Finisar
  • FTLF1421P1xCL - OC-48 IR-1/STM S-16.1 RoHS Compliant Multirate SFP Finisar's FTRJ1421P1xCL SFP transceivers are compatible with the Small Form Factor Pluggable MSA. They comply with SONET OC-48 IR-1 (SDH STM S-16.1) standards, Gigabit Ethernet and Fibre Channel. They are also compatible with SONET OC-12 and SONET OC-3. Digital diagnostics functions are available via the 2-wire serial bus.
    Finisar

Results 1 - 24 of 56

Diagnostics - Test routines run to determine errors.