Current Transducers

OMEGA’s OM10 Series watt transducers accept ac voltages and currents to produce a conditioned dc process signal output representing wattage. Single, dual, and three element models are available to accommodate a variety of wiring configurations. For larger input voltages and currents, the OM10 may also be used with OMEGA’s voltage and current transf ...more

The DP24 Series is an economical, user-friendly panel meter which can be scaled without the use of an electronic calibrator. The DP24-E accepts voltage (0 to 5, 1 to 5 and 0 to10 Vdc) or current (4 to 20 mA) transducers. After scaling, the front keypad can be locked out to avoid unauthorized changes, and an optional bezel without "buttonholes" can ...more

F6010 front panel controls are human-engineered for basic, steady-state control of voltage and current phasor quantities. Using the F6010 Controller, source control is expanded to provide the dynamic test functions of instantaneous switch-ing voltage, current, and phase angle for up to 12 sources. When F6000 Instruments are equipped with the F ...more

This series calibrators are used for adjusting, checking and verification of measuring instruments used in power engineering. These include active and reactive power meters, phase meters, frequency meters, ammeters, voltmeters, transducers, monitoring systems, and frequency, voltage and current relays. ...more

The OM9 Series transducers convert ac currents and voltages to dc process signals for direct connection to data acquisition and recording systems. The OM9 employ true RMS measurement techniques in conditioning the ac signal. True RMS measurement provides accurate readings for signals which contain harmonic distortion. For measurement of currents an ...more

The CS10 uses CR Magnetic's CR8459 Current Transformer to measure the approximate current over a range of 0 to 200 Amps. The CS10 outputs a millivolt signal allowing the transducer to be directly connected to the CR510, CR10X, or CR23X dataloggers. ...more

This series calibrators are used for adjusting, checking and verification of measuring instruments used in power engineering. These include active and reactive power meters, phase meters, frequency meters, ammeters, voltmeters, transducers, monitoring systems, and frequency, voltage and current relays. ...more

The Trig-Tek, Inc. Model 256A APS-16 Accelerometer Power Supply is designed to condition accelerometers and other transducers which require current excitation. The unit passes the signal with unity gain and provides an output with less than 100 Ohms impedance. Front panel LED's illuminate (READY) monitoring the status of the channel. The unit h ...more

The F6080 Field Calibration Module is the most effective way to keep your F6150 protection test instrument properly calibrated. Using the F6080 will increase your confidence in the accuracy of protection, meter and transducer testing. The simple, user-friendly front panel of theF6080 has clearly marked connections to connect to the F6150. Its s ...more

transducers accept ac voltage and current to produce a two conditioned dc process signal outputs representing wattage and Volt Amp Reactance (VAR). ...more

The Trig-Tek, Inc. Model 252A APS-8 Accelerometer Power Supply is designed to condition accelerometers and other transducers which require current excitation. The unit passes signals with unity gain and provides an output with less than 100 ohms impedance. Each channel has fixed, 12dB/ocy, high pass and low pass filtering. ...more

The Trig-Tek, Inc. 258A APS-8 Accelerometer Power Supply is designed to condition accelerometers and other transducers which require current excitation. The unit passes eight signals with unity gain and provides outputs with less than 100 Ohms impedance. Front panel LED's illuminate (READY) monitoring the status of the channel input. ...more

This series calibrators are used for adjusting, checking and verification of measuring instruments used in power engineering. These include active and reactive power meters, phase meters, frequency meters, ammeters, voltmeters, transducers, monitoring systems, and frequency, voltage and current relays. ...more

The Trig-Tek, Inc. Model 254A APS-4 Accelerometer Power Supply is designed to condition accelerometers and other transducers which require current excitation. The unit passes the signal with unity gain and provides an output with less than 100 Ohms impedance. Front panel LED's illuminate (READY) monitoring the status of the channel. The unit ha ...more

The DBK65 supplies transducer power and easy connectivity to the acquisition system. Attaches to P1 connector, or directly to WaveBook voltage input channels (via optional cables). Accommodates internal current-shunt resistor, selectable per channel  ...more

This series is specially designed for 24V input applications, such as various transducers and transmitters, e.g. temperature sensor, voltage and current mutual sensor, 4-20mA transmitters. ...more

The Trig-Tek, Inc. Model 103A Three Channel Power Supply is designed to provide power and normalization to voltage mode transducers. Each channel has an input sensitivity dial, which is continuously variable from .9 to 11, offering an input sensitivity range of 9 to 110 mV/g. Each channel has an output which is normalized to 10 or 100 mV/g, sw ...more

The Arbiter Systems, Inc. Model 1040C Panel Meter Calibrator (PMC) integrates eight calibration functions: voltage, current, frequency, power, power factor, phase, reactive power (VARs), and synchroscope into one compact, portable package. All of these functions in one lightweight yet rugged instrument allow you to easily calibrate virtually e ...more

This series calibrators are used for adjusting, checking and verification of measuring instruments used in power engineering. These include active and reactive power meters, phase meters, frequency meters, ammeters, voltmeters, transducers, monitoring systems, and frequency, voltage and current relays. ...more

Wilde range for most monitoring applications. Frequency range 10kHz - 100MHz. Window diameter of 25.4mm. 0dB transducer factor between 500kHz and 100MHz ...more

The Model 2100B is designed to generate voltages up to 600V and currents to 100A at any power factor from zero lag though unity, to zero lead. Completely automated, the 2100B is ideal for calibrating wattmeters, energy meters, watt hour meters, watt transducers and VA measurements to <30 PPM. ...more

The Model 2100A is designed to generate voltages up to 240V and currents to 5A at any power factor from zero lag though unity, to zero lead. Completely automated, the 2100A is ideal for calibrating wattmeters, energy meters, watt hour meters, watt transducers and VA measurements to <20 ppm. ...more

The AYA MC-Series electrical transducers incorporate the newest state-of-the-art micro-controller technology in circuit design and innovation. They provide both analog and digital output signals and they are ideal for installations that require continuous monitoring and digital logging of electrical parameters in single and three-phase electri ...more