Current Transducers

The ETR accepts a generic Analog Output signal (voltage or current) and provides variable resistance output as a simulated potentiometer. The board performs 64 step approximation with about 1.5% output resolution. For high output accuracy the ETR's resistive array utilizes a number of 1% precision metal film resistors. Their unique configurati ...more

Measuring transducer for acquiring stroke travel at valves, butterfly valves, slides and other actuators. The transducer converts the measured quantity into a load-independent direct current which is proportional to the measured value. ...more

The ATL accepts an analog voltage or current input signal and controls four relays. Each relay has an adjustable trip point which is set by a multi-turn trimmer potentiometer. Each relay is activated when the input signal is equal to or greater than the trip point setting. ...more

The Model 155 assembly consists of eight single-channel signal conditioner cards and four dual-channel alarm cards. The unit monitors acceleration, velocity, displacement, RPM, pressure, or any other critical parameter and provides AC voltage, RMS-DC voltage and 4-20mA current outputs. Two setpoints per signal are settable on the alarm cards, ...more

AC Split Core Current Transducers Series SC100 converts a monitored AC current to a proportional DC voltage of 0 to 5 Volts. AC Split Core Current Transducers Series SC100 are used to monitor motors, pumps, conveyors, machine tools and any electrical load where an analogue representation is required over a range of currents. All models are CSA ...more

To complete your displacement measurement system Magtrol offers the CST 113 Signal Converter, designed specifically for transducers delivering a signal of 4 to 20 mA. Either a voltage-based signal (I/U conversion) or a current-based signal (I/I) can be chosen as the converter output, along with signal inversion if required. A large variety of ...more

The CR4310/11 series current-to-voltage transducer produces a 0-5 Vdc output signal that is directly proportional to the input AC current. The output signal is average-sensing, calibrated for RMS. This transducer is used with process control and industrial instrumentation equipment. The DC output signal can be connected directly to a high imped ...more

The CR4100 Series True RMS Current Transducers and Transmitters are designed for applications where AC current waveforms are not purely sinusoidal. More precise and accurate than other transducers, these devices are ideal in chopped wave and phase fired control systems. ...more

Programmable multi-transducer for the acquisition of up to 51 measurements in a heavy-current power system. The DME 408-Ethernet provides to the user all necessary information for energy consumption control. ...more

Measuring transducer for the conversion of active power in single phase alternating current or 3-phase systems with balanced or unbalanced load. A load-independent direct current or direct voltage is used as an output signal, which is proportional to the measured active power value. ...more

Measuring transducer for the transformation of alternating current, self-powered ...more

The Rotek Model MSB-001A Watt Converter Standard is a high accuracy ac power to DC voltage transducer with an accuracy of 50 PPM of rated input power and a linearity of 20 PPM. The Model MSB-001A has 120 and 240 volt input ranges and 1 and 5 ampere current ranges (optional 10 and 50 ampere range). The output of the MSB001A is a DC voltage directly ...more

Current Transducer Solid Core Sentry 100 Series convert a monitored AC current to a proportional DC voltage of 0 to 5 Volts. Current Transducer Solid Core Sentry 100 Series is used to monitor motors, pumps, conveyors, machine tools and any electrical load where an analogue representation is required over a range of currents. Current Transducer ...more

32 Differential or 64 Single-Ended 16-Bit Scanned Analog Voltage Input Channels. 32-Channel Precision Scanning Excitation Current Source; 0.4ma to 10ma Options. Input Ranges Selectable as ±10V, ±5V or ±2.5V. Excitation Applied to any Channel Combination Under a Control Mask High Input. Impedance for Channels Not Requiring Excitation. Scan Rate ...more

Measuring transducer for the transformation of sinusoidal or distorted alternating current, with power supply terminal ...more

The all new CR Magnetics Data Stream Series of Electrical Properties Transducers are the most advanced electrical sensing products available in the industry. Voltage, Current, Power, Power Factor, Energy and Frequency can all be monitored in a single package. The sensed information is then provided to the system via an RS485 serial bus. Constr ...more

The CR473 series Voltage Transducers are expanded scale instruments designed to accurately measure three-phase voltages. Each model produces three discrete 4-20 mA signals which are proportional (across the selected input voltage range) to the three-phase input voltage. The output is a true constant current driver which is unaffected by resista ...more

The all new CR Magnetics Data Stream Series of Electrical Properties Transducers are the most advanced electrical sensing products available in the industry. Voltage, Current, Power, Power Factor, Energy and Frequency can all be monitored in a single package. The sensed information is then provided to the system via an RS485 serial bus. Constru ...more

Transducer for the conversion of the difference in phase angle from two electrical systems requiring synchronization into a direct current or voltage signal which is proportional to the measured value ...more

The CR5400 Series, AC/DC Hall Effect Current Transducers, are designed to provide a bipolar output that proportionally reflects the input bipolar current. These devices are specifically targeted to be used in applications where multi-mode current sensing is required. ...more

The all new CR Magnetics Data Stream Series of Electrical Properties Transducers are the most advanced electrical sensing products available in the industry. Voltage, Current, Power, Power Factor, Energy and Frequency can all be monitored in a single package. The sensed information is then provided to the system via an RS485 serial bus. Constru ...more

PD-MCC&G400A is an on-line Partial Discharge (PD) diagnostic system, which detects and analyzes the generation of PD in the power equipments such as Cable and Motor. Four High Frequency Current Transducer (HFCT) Sensors are installed ground line in power equipments to detect PD signals. PD-MCC&G400A PD-MCC&G400A is an on-line Parti ...more

The V180 is a single-width VME module that allows accurate and comprehensive measurement of AC power circuits. The V180 acquires powerline current and voltage inputs using approved current transformers and model C750 remote potential transducers. Up to sixteen CT sensors and eight potential connections (six lines plus two neutrals) can be acco ...more

The all new CR Magnetics Data Stream Series of Electrical Properties Transducers are the most advanced electrical sensing products available in the industry. Voltage, Current, Power, Power Factor, Energy and Frequency can all be monitored in a single package. The sensed information is then provided to the system via an RS485 serial bus. Constru ...more

Multi-Function System for Testing Substation Equipment. The T/3000 is a unique solution for all testing operations during commissioning and maintenance of substations. Testing can be performed on both relays of all types and on current and voltage transformers! The unit is also able to test energy meters and transducers. ...more