Current Leakage Test

Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment - saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence ...more

This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also u ...more

The model 308A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

The model 307A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also u ...more

AC Hipot Test Performs AC dielectric testing (hipot) over the voltage range from 50 to 5000VAC RMS. Leakage current detection is programmable from 1µA to 40mA, making the 6100 ideal for testing medical products and instruments having a wide range of leakage currents. DC Hipot Test DC dielectric testing is possible from 50 to 6000VDC with leaka ...more

Wide Measurement Ranges: Measure resistance from 10k to 1P with basic accuracy of ±2% up to 1T. Measure Leakage Current down to 1pA with basic accuracy of ±2%. Programmable Test Voltage: From 10V to 1kV in 1V increments on the 1868A Model, and from 50V to 5kV in 1V increments and on the 1868D Model. Powerful Charge Capability: The 1868A Model ...more

Enables non-contact measurements of ground conductors without need for auxiliary ground spikes. Autoranging ground resistance easurements from 0.025Ω to 1500Ω with 0.002Ω resolution. True RMS AC Leakage current range of 0.2mA to 30A with 1.000mA resolution. Programmable Datalogging with 116 data points. Programmable Hi/Lo Alarm ...more

Accurate ground resistance measurement from 0.025 to 1500 Ohms. TRMS current measurement including leakage current. Continuity beep if the resistance is lower than 40.00 Ohms  ...more

Larger Clamp Size (1.25"). Backlight. Ground resistance (0.1 to 1200?). Ground leakage current to 30A. Ground continuity loop test. Audible alarm. Data Storage  ...more

SCR ELEKTRONIKS have developed Patient / Earth Leakage Current Testers to measure the Leakage Current in medical appliances. The Patient / Earth Leakage Current Tester Model - PELCT-MS isdesigned to carry out Leakage Current measurement in 3 modes, namely  ...more

Small Signal and Power Discrete Semiconductor Tester. Parametric Measurements of Leakage Current, Breakdown Voltage, Gain, Saturation Voltage, On-State, Off-State, AC , Impedance, Transconductance, Capacitance  ...more

The 810 EL is S.E.W.'s tiniest professional Analog Domestic Residual Current Detector (/ Earth Leakage Circuit Breaker (ELCB) / Ground Fault Circuit Interrupters (GFCI) tester, designed to meet international standards of performance and safety. This model is a high quality instrument used by professionals to obtain accurate values of disconnec ...more

Audio / Visual Alarm When HV ON & Off Test ON/ OFF switch to start and interrupt test. Unique Data Hold facility to hold Breakdown Voltage data. Precise Trip Current Setting or press to set switch for leakage current. Inbuilt timer with selector switch.  ...more

Ross Engineering Corporation's High Voltage Megmeter is a unique battery powered HVDC source and meter. Models are available for withstand testing of insulation up to 42KV DC, as well as measuring leakage current as low as 0.001 microamp and resistance as high as 30 million megohms when testing underground cable, rubber safety gloves, vacuum in ...more

Capable of measuring earth voltage (Vac) 2mA measuring current permits earth resistance test with tripping earth leakage current breakers in the circuit under test. In addition to the facility for precision measurement, test leads for simplified two wire measuring system also supplied as standard accessories. ...more

COMBI420 is an innovative meter designed to perform all safety test verifies on electrical installations in compliance to recently standards (VDE0100, BS7671 and so on, measure and save results of environmental parameters (illuminanance, temperature, sound level), leakage currents and active power, harmonics, power factor measurements on single ...more

New rugged design to withstand industrial environment. Metal body with Collapsible steel handle. In-built hand-driven brushless AC generator and static rectifier to supply Stabilized DC voltage. Guard terminal to eliminate surface leakage current. Cross coil movement, sintered anti-friction bearings and delrin-moulded gears ensures trouble-fre ...more

Capable of measuring earth voltage (Vac) 2mA measuring current permits earth resistance test with tripping earth leakage current breakers in the circuit under test. ...more

Ten ground-fault set points from 10 to 500 mA. Ten ground-fault trip-time settings from 30 to 1,000 ms. DFT (harmonic) filter prevents false operation. 4-20 mA output for fault-current metering. Self-test input. Selectable fail-safe (undervoltage) or non-fail-safe (shunt) operating mode  ...more

Capable of measuring earth voltage. 2mA measuring current permits earth resistance tests without tripping earth leakage current breakers in the circuit under test ...more

Small Signal and Power Discrete Semiconductor Tester. Parametric Measurements of Leakage Current, Breakdown Voltage, Gain, Saturation Voltage, On-State, Off-State, AC , Impedance, Transconductance, Capacitance. Transistors, Diodes, IGBTs, Hybrids, FETs, Jfets, Zeners, IGBTs, SCRs, Triacs, Optos  ...more

Harmonics Analysis (V and A) to the 99th order in % & in magnitude. Total Harmonic Distortion (THD?F, 1?50th Order). Leakage Current Measurement at 10 m A resolution. Analysis of Crest Factor (C.F). Non-interrupted Harmonics Analysis ...more

Capable of measuring earth voltage. 2mA measuring current permits earth resistance tests with tripping earth leakage current breakers in the circuit under test. In addition to the facility for precision measurement, test leads for simplified two wire measuring system also supplied as standard accessories. ...more

SIRIUS89N is a complete model to perform all safety tests in compliance to VDE 0413, measure of values of environmental parameters (temperature/humidity, illuminance, sound level with optional probes), leakage current with optional clamp and to perform a network power quality of single phase in compliance to EN50160 guideline. ...more