Current Generators

Load Dump pulses simulate the sudden disconnection (e.g. by corrosion) of the battery from the alternator while the alternator is generating current to load the battery. Such Load Dump pulses are high energy pulses with a high potential of destruction. The LD 200N simulates these high energy pulses having a duration time in the range of hundreds of ...more

The Model 1200A series is a computerized hand-held potentiostat/bipotentiostat. The instrument consists of a digital function generator, a data acquisition system, and a potentiostat/bipotentiostat. The potential range is ± 2.4 V. The current range is ± 2 mA. This series is capable of measuring current down to 100 pA. The steady state current of a ...more

The 2226 is a digital micro-ohmmeter for fast and accurate low resistance measurements. The measuring current of 10A DC makes this instrument applicable for testing of motor coils, generators, smaller transformers, generator bars, copper wire and cable, cable screens, switches, relay contacts, shunts, potentiometers etc. Covered measuring rang ...more

Load Dump pulses simulate the sudden disconnection (e.g. by corrosion) of the battery from the alternator while the alternator is generating current to load the battery. Such Load Dump pulses are high energy pulses with a high potential of destruction. ...more

Surge pulses occur due to direct or indirect lightning strokes to an external (outdoor) circuit. This leads to currents or electromagnetic fields causing high voltage or current transients. Another source for surge pulses are switching transients originating from switching disturbances and systems faults. ...more

The MT185 performs basic tests, like line loss, noise, and level measurements. It also features a balanced tone generator, C-message weighting filter, termination mode and bridge mode. The unit is equipped with DMM functions like voltage, current, and resistance measurements. ...more

Load Dump pulses simulate the sudden disconnection (e.g. by corrosion) of the battery from the alternator while the alternator is generating current to load the battery. Such Load Dump pulses are high energy pulses with a high potential of destruction. ...more

The Model 800B series is designed for electrochemical detection. This instrument can be used for monitoring the current passing through a flow cell in liquid chromatography/electrochemistry and in-flow injection analysis, as well as other electroanalytical applications. Each instrument contains a digital function generator, a data acquisition syste ...more

The Model 1100A series power potentiostat/galvanostat is designed for electrochemical applications that require relatively large current and high compliance voltage, such as battery, corrosion, electrolysis, and electroplating. The current range is ± 2 A. The compliance voltage is ± 26 V. The instrument contains a digital function generator, a data ...more

The model 1000A series is a computerized 8 channel potentiostat. The system contains a digital function generator, a multiplexed data acquisition circuitry, a multi-potentiostat can work with eight independent cells, or eight working electrodes in the same solution with a common reference electrode and a common counter electrode. The potential cont ...more

The FCC-TG-115A is a coaxial charge line type of pulse generator designed to generate a trapazoidal shape output pulse. It is designed primarily to drive current injection probes to inductively couple current onto cables bundles to satisfy the CS-115 test requirements of Mil Std 461/462D and Mil Std 461E. ...more

T-302 H.V. Surge Generator is mainly used to test high resistance fault and flashover fault for power cable of 3~10kV. In conjunction with the T-903 Power Cable Fault Locator and the T-505 Pinpoint Fault Locator for fault locating. Matching with the special digital micro ammeter, T-302 can also perform Current Leakage test for cable of 6kV and ...more

For exponential current impulse ECI 1/20us, 4/10us, 8/20us and lightning current impulse LCI 10/350us applications with impulse current amplitude up to 200kA. ...more

Performs DC parametrics and functional tests. 10MHz pattern generator. Characterize flash memory cell current and MRAM magnetoresistive properties. Algorithmic Pattern Generator Packaged devices or wafer test. ...more

The Model 700C series are computerized general purpose potentiostat / bipotentiostats / galvanostat instruments. A typical application involves a rotating ring-disk electrode (RRDE), but these systems can also be used for other applications where dual channel measurements are essential, such as dual channel electrochemical detection. The system con ...more

The ITC57600 Tester is a programmable current waveform generator that is used to surge, test and measure voltage breakdown on many different device types. These include Transient Voltage Suppressor (TVS) diodes, as well as MOSFET and BIPOLAR Transistors, Zeners, Rectifiers, MOVs, Polyswitches and PTC devices.  ...more

Clear identification of a cable before it is cut or fi tted is a task with absolute relevance to safety. Any mistakes here can have fatal consequences for the cable fi tter and cause outages for the connected customers. The CI cable identifi cation system has been designed for even simpler, safer working. The system consists of the current puls ...more

Two, 4-1/2" meters: Voltmeter, 0-18-0-36 for testing operating voltage. D.C. ammeter dual scale 10-0-100/120 amp for testing alternators and 30-300 amp for testing free running starters. One 3" D.C. ammeter 10-0-10 for testing field current. Duplicates the circuitry found in an automobile. Tests 6-12-24 volt. A or B circuit. Motor rev ...more

GIS could be used as current generators in a variety of applications, as activation and hold-on tests for switches and protection relays, primary current injection tests, precise evaluation of circuit breakers, heating tests for contacts, cablings and electric equipments.  ...more

8 channel, 16 bit D/A, Wave RAM generator functions, low current versions, front panel I/O, 3U. ...more

The ohmmeter RMO100M is designed for resistance measurement of electrical motors and generators. RMO100M generates true, filtered DC current. The test result is displayed as R=U/I. The RMO100M instrument can store up to 500 measurements. All measurements are time and date stamped. Using RMOWin-M software a test can be performed from a PC, and t ...more

This instrument contains three separate generators: a main generator that generates either AC Current, AC Voltage or DC Voltage; auxiliary AC Voltage generator that generates an idependent, phase shiftable AC Voltage; and an auxiliary DC Voltage generator that generates the DC Voltage that feeds the relay under test. ...more

The PTE-50-CET equipment is a universal, portable, test system with three outputs to test single and three phase protective relays. The equipment comprises of three independent output channels that can be selected as current or voltage. This enables the unit to be used as a complete single-phase equipment (voltage, current, and phase angle between ...more

Three-phase power/energy calibrator M-103 is generator of accurate AC three-phase voltage and current with calibrated phase shiftamong signals. It contains three voltage and three current channels, which phase shift each of them against others can be set in rango 0 to 360o. Output voltage can be set in two ranges up to 240 V and output current ...more

The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT?s, digital filtering, etc. Application software can be downloaded to the DSP via the CPCI interface. ...more