Current Clamps

B+K Precision offers a wide variety of current clamps for safe non-invasive current measurement. Measure up to 2000A with these reliable, rugged instruments. All of B+K Precision clamps are much more than a current clamp offering the ability to measure, voltage resistance, capacitance and even frequency. Additionally, special features allow fo ...more

The 301 is intended to be used with an AC Current Clamp Meter. It provides temporary separation of conductors to facilitate measurement of current. Most 120Vac devices use a two conductor power cord which makes it difficult to isolate a single conductor to make a current measurement. A single conductor is required to make a measurement because ...more

With the striking design of the Fluke 330 Series, we've taken a new look at the way you make current measurements. At how you use your tools, and how to get the results you need, faster and more conveniently. The result is a new, ergonomic concept, shaped to fit your hand and to access tight spots easily. The series feature a large display tha ...more

High current and a large jaw, make this clamp well suited for industrial and utility applications. Safety ratings of CAT IV 600 V, CAT III 1000 V add excellent user protection. Confidently take reliable readings with these True-rms, clamp meters; the tools of choice for high current measurement up to 2000 A. ...more

Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools. Battery-powered Hall-effect probe measures 1A to 400 A. 1mV/Amp output guarantees easy reading on your meter. Take accurate current readings without breaking the circuit. Maximum conductor Ø 32 mm. ...more

Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools. Battery-powered Hall-effect probe measures 1 A to 1000 A. 1mV/Amp output guarantees easy reading on your meter. Take accurate current readings without breaking the circuit. ...more

The clamp-on ground testing technique used by the Fluke 1630 simplifies ground loop testing and enables non-intrusive leakage current measurement. The compact and rugged design makes the Fluke 1630 easy to use in small places and harsh environments, while the "display hold" and the continuity testing with an audible alarm function en ...more

Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment - saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence ...more

Fluke Current clamps are the ideal tools to extend the functionality of Fluke tools. The i400 is a single range 400 A ac current clamp with current output via safety shrouded banana plugs. The clamp is compatible with most Fluke multimeters or any other current measurement device that accepts 4mm-shrouded banana plugs and has an AC milliamp ra ...more

Measure up to 2000A with this reliable, rugged instrument. Many of B+K Precision clamps are much more than a current clamp offering the ability to measure, voltage resistance, capacitance and even frequency. Additionally, special features allow for the recording of minimum and maximum values, peak values, test diodes and for continuity. ...more

The Fluke i1000s is a clamp-on ac current probe designed to expand oscilloscope applications in industrial and power environments. The Current Probe (shown in figure) provides the following features: Ideal for measuring distorted current waveforms and harmonics. Allows accurate measurement of currents from 100 mA to 1000 A rms, 5 Hz to 100 kHz with ...more

The Fluke 321 and 322 are designed to verify the presence of load current, AC voltage and continuity of circuits, switches, fuses and contacts. These small and rugged clamp meters are ideally suited for current measurements up to 400 A in tight cable compartments ...more

Fluke Current clamps are the ideal tools to extend the current ranges of Multimeters. The i200 is a single range 200A ac current clamp with current output via safety shrouded banana plugs. The i200 is compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs. Companion to a DMM to measure up t ...more

True RMS (TRMS). Measures AC Voltage. Measures DC Voltage. AC Current to 1000A   ...more

Measurements: Total Harmonics Distortion THD, AC/DC Voltage up to 600V, AC Current up to 1000A, Resistance, Frequency, Temperature. Data-logging 5400 points. ...more

Voltage and Current Harmonics up to 25th with THD%. Frequency (with test leads and jaw). Phase sequence with single wire (patented) ...more

Measurements: AC/DC Voltage up to 600V, AC Current up to 1000A, Resistance, Frequency and Temperature. Data-logging 5400 points. Optional PC interface capability (RS-232 KIT2). Audible continuity. ...more

Accurate ground resistance measurement from 0.025 to 1500 Ohms. TRMS current measurement including leakage current. Continuity beep if the resistance is lower than 40.00 Ohms  ...more

Conform to the IEC1010-1 & IEC1010-1-032 standard. Double insulation (protection class 600V CAT III and pollution degree 2). Display: 3999 counts and 42 segments bar graph. Auto/Manual range. True RMS for AC voltage and current. Auto zero key for DCA  ...more

600A AC current. Digital thermometer to 400 °C (1000 °F), Type K probe included. AC/DC Volts 750 V/1000 V. Capacitance to 4000 µA for motor run/start capacitor testing. ...more

AC current measuring capability up to 400 amps. Compact size, fits easily into tool pouch. Data hold and Max hold to capture important readings. Amperage Measurement: 20.00, 200.0, 400 A Display: 2000 count LCD Jaw Opening: 1.06' (27 mm) Measurement. ...more

TRMS sensing. AutoVA - Auto Selection of AC Volts, DC Volts or AC Amps. Measurements: AC/DC Voltage up to 600V, AC Current up to 1000A, Resistance, Frequency. Active (W), Reactive (VAR) and Apparent (VA) Power with dual-display Power Factor readout,Temperature. ...more

AC Current up to 400A AC/DC Voltage up to 600V. Active, Reactive and Apparent Power Single/Three Phase. Phase sequence with single wire (patented) ...more

Conform to the IEC61010-1 & IEC61010-032 standard. Double insulation (protection class 600V CAT III and pollution degree 2). Inrush function. The over-molding rubber case protects the meter to be stronger. Clamp on frequency function. Auto range/manual range. Data hold. Maximum/minimum value measurement. Auto power off  ...more

The Clamp-On Meter Model F3N is designed to take measurements on low and medium power electrical installations in conductors carrying a peak current of no more than 1000A. The True RMS current measurement range extends from 300mA to 400A.  ...more