Continuity Testers

The new Fluke T3 is a voltage and continuity tester that is designed to work long and hard. There are no settings, just probe the circuit and the T3 will show you whether you are looking at AC volts, DC volts, or an open circuit. You don't even have to turn it on or off! With seven different voltage indicators, it can clearly differentiate bet ...more

The HTT-1 was designed to provide a fast, safe and reliable way to verify proper operation of Dielectric Withstand (hipot) and Ground Continuity Testers between calibration cycles. It allows the operator to check the result of the three failure modes encountered in production hipot and ground circuit testing (open ground, high leakage current, ...more

The HT-2000 is a production line AC Hipot Tester. AC Hipot testing is best for: Portable Lamps. Fixtures. Medical Equipment in the Patient Care area. Products not using Y capacitors. Other applications where AC Hipot Testing is mandated. It can generate up to 2000V at 20mA.This tester performs the dielectric withstand and ground continuity pro ...more

The GF-30AC is a production line workhorse. This unit delivers a constant AC current while checking impedence. This unit protects product under test as internal current limiting prevents over-current excursions. Test results indicated by red and green LED's, audible buzzer on failure V=IRtual voltage sense circuit compensates for any resistanc ...more

The model 307A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

The model 308A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

With Anue's CHASSIS, LINE CARD, and SOFTWARE LOAD building blocks, many different combination systems can be configured. For example, a Network Emulator can contain both Gigabit Ethernet and Fibre Channel Signal Delay and impairment capability, or SONET Signal Delay and Path Delay capability, etc. • WAN testing • VoIP network testing • Ether ...more

The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA 568A, TIA 568B, and Token Ring cables within a few seconds. It detects miswiring, polarization, and continuity. The 230A also tests the ground of shielded twisted pair cables. With the remote unit, you can remotely test installed cable either from the wall plate or pat ...more

The 231A can easily read the correct pin configuration of 10BaseT cable (category 5), 100BaseTx, 10Base2 cable (coax) and RJ45/RJ11 modular cables, 356A, TIA 568A, TIA 568B and Token Ring cables by comparing one transmitting end to the corresponding receiving end. With the remote kit, it can test cables installed far away either on wall plate ...more

The Fluke T5 Electrical Testers let you check voltage, continuity and current with one compact tool. With the T5, all you have to do is select volts, ohms, or current and the tester does the rest. OpenJaw current lets you check current up to 100A - without breaking the circuit. Its tough test leads stow neatly in the back of the tester, making ...more

The T+PRO and T+ Electrical Testers offer all the functionality that electricians look for in volt meters and voltage and continuity testers: Both have three ways to detect ac/dc voltage: light, sound, and vibration. Both offer the added functionality of a GFCI trip and continuity beeper, plus the convenience of a built-in flashlight ...more

The 7-600 tester is designed for safe, automatic measurements of ac volts, dc volts, resistance and continuity. Simply turn on and use. ...more

The T+PRO-1AC Kit combines two troubleshooting tools, in one convenient combo pack. The T+PRO Electrical Tester has all of the advantages of a traditional solenoid tester, with added functionality, but none of the typical drawbacks. With voltage measurement, continuity, built-in flashlight, GFCI trip capability, and the legendary ruggedness an ...more

Cablescans line of microprocessor-based testers/build aids is designed to enable you to select from a wide variety of configurations number of test points, optional printer, optional PC, program storage by EEPROM or Floppy, etc. They do, however incorporate a number of features that are common to all of them. ...more

Cablescans line of microprocessor-based testers/build aids is designed to enable you to select from a wide variety of configurations number of test points, optional printer, optional PC, program storage by EEPROM or Floppy, etc. They do, however incorporate a number of features that are common to all of them. ...more

The Series 90HV combines low-voltage solid-state technology with high-voltage relay technology ¾ solid-state devices for testing continuities and components at low voltage; relays for testing high-resistance isolation and high-current continuity. The high-resistance isolation tests are typically used to test the quality of harness insulation m ...more

Cablescans line of microprocessor-based testers/build aids is designed to enable you to select from a wide variety of configurations number of test points, optional printer, optional PC, program storage by EEPROM or Floppy, etc. They do, however incorporate a number of features that are common to all of them. ...more

Cablescans line of microprocessor-based testers/build aids is designed to enable you to select from a wide variety of configurations number of test points, optional printer, optional PC, program storage by EEPROM or Floppy, etc. They do, however incorporate a number of features that are common to all of them. ...more

Cablescans line of microprocessor-based testers/build aids is designed to enable you to select from a wide variety of configurations number of test points, optional printer, optional PC, program storage by EEPROM or Floppy, etc. They do, however incorporate a number of features that are common to all of them. ...more

Bulb Lights when circuit is completed. For use with unenergized circuits ...more

Extremely easy to use, no buttons, no setups. Automatically selects AC Voltage, DC Voltage or Continuity. Automatically turns ON and OFF  ...more

AC/DC voltage and polarity measurement LCD and dual color LEDs for convenience Selectable SHAKER feature when measuring AC voltage Overvoltage warning gives user visual notification that voltage levels have exceeded 1000V AC/ 380V DC Auto-hold automatically activates when tester is removed from voltage reading. Continuity test and single probe ...more

The NETest-E is designed to provide quick and clear results for testing network cable continuity and wiring configuration. It will detect the most common wiring faults on TIA568A/568B, Token Ring, 10BASE-T, and 10/100BASE-T twisted-pair cables. The faults detected by the NETest-E include shorts, miswiring, reversed pairs, and shielding faults ...more

The Ribbon Cable Tester is designed to test the most commonly used flat IDE cables for wiring continuity, opens, shorts and miswiring. An intelligent CPU will memorize the correct wiring configuration for an IDE cable, thus enabling mass production cable assemblies to test one cable after another for pass or fail status. ...more

MS2600 is an open jaw digit electrial tester. There are DCV, ACV, ACA, Ω, CAP, frequency, diode test, continuity test and duty cycle test function. Moreover, there are auto and manual range, relative measurement, data hold, and backlight auto off time limit mode. Test leads can be inserted on groove of back of the tester. ...more