Conditioners

The 28316B 16-Channel Long Distance TEDS/IEPE Accelerometer Conditioner provides signal conditioning for either TEDS equipped or traditional IEPE sensors. Ideal for modal and structural analysis applications, the 28316B card is equipped with Precision Filters? long-distance TEDS (LDTEDS) technology that extends communication with TEDS equipped ...more

The 28208 Octal Thermocouple Conditioner provides eight channels of conditioning for thermocouples or other DC and AC voltage inputs. The 28208 consists of a low-drift programmable differential pre-amplifier, a 3-pole programmable filter and a programmable post-amplifier. A rugged remote isothermal block with digital temperature sensor provide ...more

28104A Quad Bridge Conditioner offers four channels of conditioning to support a wide variety of transducers including those that require constant voltage excitation in a bridge configuration such as strain gages and pressure transducers. The 28104A is easily configured to operate as a precise voltage filter/amplifier on low-level AC or DC vol ...more

The Series SCC Signal Conditioners provide maximum accuracy with minimal cost. Built-in microprocessor digitally scales, amplifies, linearizes and isolates thermocouple, RTD, current, voltage, frequency or potentiometer analog input signals. Units offer 16-bit input resolution with 0.05% full scale accuracy. Eliminate ground loops with 1500 VA ...more

The V385 is a VME/VXI compatible eight-channel strain-gage signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the Model V380's single excitation supply. Key to the V385's increased precision is a separate remotel ...more

The 6060 is a two-channel signal conditioning amplifier-digitizer module with 50 kHz or 100 kHz bandwidth and both digitized and analog outputs. The bridge input is ten-wire shielded with programmable constant voltage or constant current excitation and programmable completion for quarter, half and full bridge transducers. Automatic bridge bala ...more

The NEW Krohn-Hite Model 39128 Multichannel Filter/Signal Conditioning System is a mainframe chassis that houses up to sixteen, 8-channel plug-in filter/amplifier cards providing as many as 128 channels of cost effective signal conditioning over the frequency range from 1Hz to 100kHz. Each plug-in card can be a filter, an amplifier or a mix of ...more

28454A Quad Conditioner with Balanced Current Excitation accommodates single arm static or dynamic strain gages, RTDs or other resistive transducers that require constant current to excite them. A unique balanced excitation circuit delivers accurate current yet has excellent immunity to noise pickup. Dynamic strain measurements may be made usi ...more

Bemco PTS-V Portable Servo Conditioners provide a closed loop flow of controlled temperature air or gas to an insulated enclosure or structure. Bemco high pressure gas servo conditioners provide air or gas at up to two atmospheres of pressure to heat exchangers and thermal shrouds. Bemco HPG High Pressure Gas Conditioners are described on a se ...more

PAO, a fluid that does not react with water and is compatible with most metals, is the basis of the Bemco PAO-II series of fluid conditioners. Similar to the Bemco PCL Chillers, PAO-II Liquid Chillers are furnished as free standing caster mounted systems, ready to provide a reliable and precisely controlled flow of temperature conditioned PAO ...more

28314 Quad Channel Wideband Charge/IEPE Conditioner provides signal conditioning for both Charge or IEPE type sensors. The 28314 features 200kHz filtered and 500kHz wideband bandwidth for shock and vibration applications. In Charge mode, ultra low drift and very large time constant circuits allow for both quasi-static charge measurements and a ...more

Universal design like its predecessor the MH-C777 accommodates almost any battery pack for digital cameras, two-way radios, cellular phones, camcorders, individual battery cells and more. Analyze (Discharge Only Function) the battery pack to obtain the discharged capacity of a battery pack, which is retained on the screen until the reset button is ...more

The Magtrol MVD 100 Digital Conditioner is a load-force-weight conditioner specially designed for strain gauge transducer applications. It is flexible and fully configurable due to 3 pressable buttons located inside the unit. These buttons allow the unit to be easily installed, requiring no solder connections.  ...more

Daytronic has four product families, the 2000 Series, the 3000 Series, the 3500 Series and the 4000 Series, designed to serve as Signal Conditioners and Controllers. Completely stand-alone in nature, these units can provide a low-noise system front-end, autonomous application control, operator display interfacing, remote data acquisition and s ...more

Daytronic has four product families, the 2000 Series, the 3000 Series, the 3500 Series and the 4000 Series, designed to serve as Signal Conditioners and Controllers. Completely stand-alone in nature, these units can provide a low-noise system front-end, autonomous application control, operator display interfacing, remote data acquisition and s ...more

The 906 Standard and the 907 Explosion-proof Hall Effect sensors produce digital pulse signals for use with speed switches, tachometers, counters, signal conditioners, or as direct pulse generators. ...more

Daytronic has four product families, the 2000 Series, the 3000 Series, the 3500 Series and the 4000 Series, designed to serve as Signal Conditioners and Controllers. Completely stand-alone in nature, these units can provide a low-noise system front-end, autonomous application control, operator display interfacing, remote data acquisition and s ...more

The V380 is a VME/VXI compatible eight-channel strain-gage signal conditioner which is optimized for load-cell weighing applications. The module includes tare (zero reference), DSP-based high-order filtering, averaging, triggered weighing, and other functions not commonly available in conventional strain-gage signal conditioners. Filtering and ...more

The 906B and 907B-XP Quadrature Hall Effect sensors produce digital pulse signals for use with speed switches, tachometers, counters, signal conditioners, or as direct pulse generators. ...more

Literally, this means a signal adjuster receiving voltage or current source outputs from sensors to adjust so that the signals are outputted for measuring them. The basic functions of them are to change the physical volume to voltage using the sensor, amplify the minute voltage and insulate inputs/outputs ...more

The 906 Standard and the 907 Explosion-proof Hall Effect sensors produce digital pulse signals for use with speed switches, tachometers, counters, signal conditioners, or as direct pulse generators. ...more

The M Series bring Yokogawa performance and reliability to the popular plug-in style. Plug-in type construction provides easy for instrumentation planning, field wiring and maintenance. ...more

For use with Magtrol Load Monitoring Units (LMUs) and Load Conditioners (AN Series), these high quality, large character digital displays are used for crane weight display, process weight display and all weighing applications. They use microprocessor based technology for high reliability and have a nonvolatile memory for all calibration data. ...more

VJ Series signal conditioners have a compact, space-saving plug-in style design. The lineup includes a universal input type, versatile I/O specifications, wide-range of power supply, isolated two outputs and field configurable models. ...more

The Model 146 is a strain gage conditioner that is particularly well-suited for load cell applications. It provides bridge excitation, high gain, low output noise and adjustable frequency response. Each module features a 4½ digit LCD display, switch-selectable to show excitation or amplifier output. Two- and four-module benchtop carrying cases ...more