Filter Results By:

Products

Applications

Manufacturers

Showing results: 226 - 240 of 473 items found.

  • Standard Tests

    LXinstruments GmbH

    The following list contains only the most important standards and does not claim to be complete.EN 60204-1 Electrical equipment of machinesEN 60335-1 Electrical appliances for household and similar useEN 50106 Sampling test, routine tests (in conjunction with EN 60335-1)EN 60598-1 LuminariesEN 60601-1 Medical electrical equipmentEN 60730-1 Automatic electrical controlsEN 61010-1 Measuring, control and laboratory equipmentEN 61439-1 Switch cabinet and switchgearEN 62368-1 Equipment for audio/video, information and communication technologyEN 62841-1 Hand-held electric toolsEN 50191 Erection and operation of stationary and non-stationary electrical test equipmentLVD Low V oltage D irective _

  • Signal Chain µModule Receivers

    µModule® - Analog Devices Inc.

    Analog Devices µModule® (micromodule) receivers consist of high performance, high speed ADCs with fixed-gain, high speed amplifiers and antialias filters. Our integrated ADC and driver products include integrated bypass capacitance and simplify the high frequency layout required to preserve ac performance. The board space savings are significant for instrumentation applications such as spectrum analyzers, oscilloscopes ,and communications test equipment, or for communications applications such as high sensitivity receivers, software-defined radio (SDR), or signal intelligence receivers. Our portfolio uses system-in-package (SiP) technology similar to multichip modules (MCM) to integrate components with different technologies, along with passive components to make an integrated subsystem.

  • Gen-Z

    Teledyne LeCroy

    Gen-Z is a data-access technology designed to provide high-speed, low-latency, memory-semantic access to data and devices via direct-attached, switched or fabric topologies. Gen-Z components use low-latency read and write operations to directly access data and use a variety of advanced operations to move data with minimal application or processor involvement. Gen-Z fabric utilizes memory-semantic communications to move data between memories on different components with minimal overhead. Memory-semantic communications are extremely efficient and simple, which is critical to delivering optimal performance and power consumption. Teledyne LeCroy provides protocol analysis and error injection test equipment to support development and debug of Gen-Z based devices

  • Digital I/O Adapter Module For FlexRIO

    NI

    Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.

  • Open Networking

    UNH IOL

    We are committed to the ever changing world of Data Communication and Storage Networks. As the industry moves forward into Open Networking, we are keeping pace. Working closely with various Open Network organizations such as the Open Compute Project (OCP) and the Open Platform for NFV (OPNFV), we are leveraging years of experience of effecting positive change in the industry and creating robust test programs to enable markets.

  • Analyzer for Safety Agency Production Line Testing

    HypotULTRAIII - Wavecontrol, S.L.

    Ethernet Communication CardUSB/RS-232, GPIB & Printer InterfacesData Storage CardInterconnection to Modular Scanning MatrixOptional 10 Volt Analog InterfaceStorage of up to 50 setups with 30 steps per setupPatented SmartGFI® functionPatented prompt and hold functionPatented CAL-ALERT® functionPatented VERI-CHEK® functionReal Current measurementDual Continuity test modesBuilt-in security settingsLine and Load regulation

  • Photonic Networks and Systems

    Fraunhofer Institute for Telecommunications

    The Photonic Networks and Systems Division develops solutions for high-performance optical transmission systems for use in in-house, access, metro, long-distance and satellite communications networks. The researchers are focusing on increasing capacity as well as improving safety and energy efficiency. The department has the latest measurement technology, very well-equipped system laboratories, powerful simulation tools and the ability to carry out field tests.

  • Cable Fault Locator

    TX2001 - BI Communications

    Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads

  • Mobile Range

    Raytheon Company

    Mobile Range™ is an integrated suite of communications, optics, and telemetry capabilities, which can be deployed anywhere in the world on land, at sea or in the air with minimal support staff or infrastructure. It enables in-country flight testing, demonstrations, and data collection in a variety of environments and conditions. The system has the ability to test anything that has an RF-transmitted data stream and can be set up and operational in as little as four hours.

  • 50 GHz Digital Setp Attenuator

    PE43508 - pSemi Corp.

    The PE43508 is a 50Ω, HaRP™ technology-enhanced, 6-bit RF digital step attenuator (DSA) that supports a wide frequency range from 9k to 50 GHz. It supports 1.8V control voltage and optional VSS_EXT bypass mode to improve spurious performance, making this device ideal for test and measurement, point-to-point communication systems, and very small aperture terminals (VSAT).

  • WAN Tester III

    TELINC Corporation

    The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.

  • High-Reliability Voltage Controlled Oscillators

    Fairview Microwave Inc.

    16 Models with Frequency Bands ranging from 10 MHz to 4350 MHz. 0.5" Hermetically Sealed Surface Mount Package. 50 Ohm Internal Matching. Designed to meet MIL-STD-883 and MIL-STD-202 Test Conditions. Wide Voltage Tuning Range from 0.5V to 20V. Phase Noise as low as -120 dBc/Hz @ 10 KHz offset. 2nd Harmonics as low as -25 dBc. RoHS and REACH Compliant. All models are EAR99. These products are used in military electronics, SATCOM, test and measurement and wireless communications.

  • ICD 3 Test Interface Module

    AC164113 - Microchip Technology Inc.

    The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.

  • Wireless Connectivity Tester

    CMW270 - Rohde & Schwarz GmbH & Co. KG

    The R&S®CMW270 is the ideal test solution for integrated wireless communications solutions as used in laptops, netbooks, game consoles, data cards, wireless headsets and other products of the IoT market. Within the R&S®CMW500 - Production Test product family, the R&S®CMW270 offers functionality tailored to the above applications. The tester provides network emulation (signaling mode) for WLAN and Bluetooth® as well as generator and analyzer functionality for standards such as WLAN, Bluetooth®, GNSS and broadcast technologies.

  • Battery Test Systems

    Intepro Systems

    The Intepro’s battery test systems are configurable systems designed to test the latest Lithium Ion batteries and other high power density batteries and chargers. Combining high resolution, high powered charge and discharge systems, Intepro IBT line of battery test systems link to the battery management through the bus communication and fail-safe external monitoring of key battery parameters.

Get Help