Clocks

2 Channel hi-speed binary serial data with clock and enable/sync signal. Variable length messages. Bit rates up to 8 Mhz. ...more

90MHz 32-bit Motorola Coldfire M5307 CPU, with a processing capacity of 75 MIPS; 16MB SDRAM, 2MB Flash Memory; One 10M Ethernet 10BASET Interface (RJ45), two Asynchronous Serial-ports (UART), one I2C Bus Interface, Real-time Clock, Watchdog Timer Hardware, Four-channel DMA and Dual 16-bit Timers; Two 84-line connectors connecting almost all da ...more

The PX467S is a precision oscillator source that provides a highly accurate and stable clock reference that can be used as a frequency or time reference that can be used as a frequency or time reference. Using selectable switches, the output of the on-board ovenized oscillator can be output as is or divided by any value from 2 to 16383. The resulti ...more

Provides GPS timing in an ANSI standard M-module format. Up to 12 satellites can be simultaneously tracked to provide extremely accurate output timing. The module can be used to discipline precision oscillators to provide long-term clock stability. The PPS output signal is software controlled to be always ON, always OFF, or only ON when certain acc ...more

The PX466S provides distribution of clock signals to other devices. The module accepts three analog input signals and provides TTL and ECL distribution. The input signals are passed through high speed comparators that convert the analog level to a digital signal. The digital signals are individually buffered to provide the TTL and ECL outputs. Inte ...more

The 6011 represents a new concept of programmable RF and microwave attenuators offering performance and features not found in traditional attenuators. It provides attenuation of up to 80 dB in steps of 0.05 dB and a minimum program step time of 2 us. The outstanding performance, flexibility and ease of use of the 6011 makes it an ideal tool fo ...more

This adapter enables the connection of chip-level devices, such as analog-to-digital converters, digital-to-analog converters and sample rate converters, to Audio Precision 2700 Series and System Two Cascade Plus audio analyzers. Devices under test may have a variety of interface protocols, including different logic families and voltage levels ...more

This MWJ-6393, Blu-Ray Disc Jitter Meter is designer for measuring and indicating the jitter conponents of the data signals (1-7 modulation signals) from Blu-ray Disc drives employed as input signals and the clock signal extracted by the internal PLL circuit employed as a reference signal. ...more

Merging the power of the TITAN with the popular formfit of our legendary ETS systems, HiLevel proudly offers the Griffin. This system provides up to 512 logic pins, 400MHz clocks, mixed signal, and data rates of up to 200MHz. The Griffin is not only low cost, but a powerful tool for Design Verification, Failure Analysis, and Production. ...more

The EVENT110 is a miniature, low-cost, recording device which senses input transitions or contact closures from external sources such as transducers and/or event initiators and records the time that a particular event has occurred. The device can store up to 13,107 time stamped events. Once activated the EVENT110 senses and records transition ...more

Built-in 32.768 kHz crystal unit allows adjustment-free. 32.768 kHz clock frequency output. 48.005120MHz PLL oscillation frequency output. Support low current consumption mode by deviding power supply of 32.768 kHz and PLL oscillation cuircuit. ...more

3.3V operating voltage, Differential LV-PECL output. Generates high frequency clock with fundamental mode. Very low jitter and low phase noise. Ceramic package with 1.2 mm Typ.theckness. Excellent shock resistance and environmental capability. Provided with output enable function (OE). ...more

The TEMP110 is a miniature, battery powered, stand alone temperature recorder. The TEMP110 features a real-time clock module that extends the battery life to > 10 years* and allows for high speed downloads. This is an all-in-one compact, portable, easy to use device that will measure and record up to 32,767 measurements ...more

The frequency standards from Pendulum suit the highest demands for stability. All frequency standards offer multiple buffered outputs (5x or 10x outputs of 10 MHz sine). Choose from the low-cost 6688 based on a very-high-stability oven-controlled SC-cut crystal oscillator or the 6689 with a built-in Rubidium atomic clock. ...more

The BERTScope CR, BERTScope CR HS (High Sensitivity), and CRJ (Jitter Analyzer) are fully flexible clock recovery instruments designed to make compliance testing of today?s communication devices easy and exact. With jitter being such a complex and contentious parameter, each clock recovery instrument is intended to make compliance testing simp ...more

The DDS5m Lockable Digital Synthesizer Module is a Precision 40 MHz Signal Source on a small circuit board. The DDS5m can be locked to an external frequency standard to provide accuracy and stability equal to the standard. It provides both Sine and Clock outputs from 100 Hz to 40 MHz in 0.025 Hz steps. The RS232 serial interface makes it easy ...more

Dual 16-bit A/D Converters. Xilinx Virtex-4 LX or SX FPGA. 32 Mbytes of QDR SRAM in four banks. 40 to 130 MHz sample clock frequency. On-board fixed frequency synthesizer. FPGA core library for data interfaces  ...more

The autosynchronous bus (AS bus) bridges are used to synchronize multiple digitizer modules together, taking care of the distribution of all necessary trigger and clock signals. Synchronous digitizing improves the accuracy of cross-channel measurements and is essential for accurate time correlation. The AS bus system can be used to phase-synch ...more

The SIM900 Mainframe is the platform on which a SIM system is assembled. The mainframe provides power, computer interfaces, clock synchronization, and individual module status. Eight internal module slots accommodate single-width and double-width modules. ...more

Dual 14-bit (105 MSPS) A/D Option. Dual 12-bit (210 MSPS) A/D Option. Single 8-bit (1.5 GSPS) A/D Option. AC or DC Coupled Analog Inputs. Selectable A/D Sample Clock Frequency. Internal/External Clock and Triggering. Xilinx Virtex-II XC2V3000 to XC2V8000  ...more

The MS4S1M is a SiGe 4-to-1 multiplexer (without integrated clock multiplying unit) designed for use in 40 or 43 Gbps SONET OC768 / SDH STM256 applications. The module accepts input data rates from 5.5-11.5Gbps with an input sensitivity better than 100mV. ...more

The Centellax TR1C1-A is a cost-effective 622MHz to 13.5GHz Clock Recovery Unit designed for signal integrity lab applications requiring multi-rate clock recovery. The CRU can be used for SFP, fiber, and other photonics applications where polarization mode dispersion changes the data period, and for other applications where degraded data requir ...more

Online System & Double-Conversion Technology 3 Phase Input, 3 Phase Output ,10 ? 150 kVA  Galvanic isolation transformers included  Up to 91% efficiency  Pure sinewave output  Real time clock  1 year full warranty  32 Recorded real-time events history  Input/output customization available  Compatible with international standards  ...more

The PCI2PMC ( PCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCI2PMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit data with 33 or 66 MHz bus operation. The PMC user IO connector Pn4 is brought out to two connectors for acces ...more

The serial Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The programmable output rates and a user oscillator position allow for flexible frequency selection. The adaptable interface allows for bursted or continuous operation, and all kinds of data / handshake prot ...more