Cables

The Fluke 1550B is a digital insulation tester capable of testing switchgear, motors, generators and cables at up to 5000 V DC. It can be used for a wide range of tests: from simple spot checks to timed tests and breakdown tests. Measurement storage and PC interface software make it ideal for preventive maintenance. ...more

Tone Generator: The Tone Generator is a hand held, battery powered instrument designed to perform a variety of tests on unenergized telephone lines or LAN cables. Alligator clips and a standard RJ11 plug allow the tone generator to be connected to stripped wires, terminal panels, wall plates, or modular single line jacks. Cable Tracer: The Lin ...more

The B+K Precision Model 205 Universal Cable / Harness Tester tests just about any cable or harness in fractions of a second. It is a compact, stand alone unit that can be used for any type of wired assembly. Opens, shorts and miswires are detected immediately. The universal adapter card offers outstanding flexibility and convenience, ready to ...more

The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA 568A, TIA 568B, and Token Ring cables within a few seconds. It detects miswiring, polarization, and continuity. The 230A also tests the ground of shielded twisted pair cables. With the remote unit, you can remotely test installed cable either from the wall plate or pat ...more

MSRP $175.00 The model 206 cable tester is a stand alone test device. It is designed to test popular PC data cables, printer, monitor, modem, mouse extension, game, BNC coax, RJ45, 1394, and USB cables by identifying the wire connection status: open, short, cross, miswire, and continuity of wires and pin configuration. It is a very good tool f ...more

The 231A can easily read the correct pin configuration of 10BaseT cable (category 5), 100BaseTx, 10Base2 cable (coax) and RJ45/RJ11 modular cables, 356A, TIA 568A, TIA 568B and Token Ring cables by comparing one transmitting end to the corresponding receiving end. With the remote kit, it can test cables installed far away either on wall plate ...more

PCB Adapter, Receiver, 192 Position QuadraPaddle to NI PXI-2529 with six 20" cables ...more

PCB Adapter, Receiver, 192 Position QuadraPaddle to NI PXI-2532 with 20" Cables ...more

25/150MHz Bandwidth# X1/X10 Attenuation# 48" (1.2m) Cable length# Includes a full accessory kit with a Sprung Hook, Replacement Tip and BNC Adapter.# IEC61010-2-031 ...more

15/90MHz Bandwidth# X1/X10 Attenuation# 48" (1.2m) Cable length# Includes a full accessory kit with a Sprung Hook, Replacement Tip and BNC Adapter.# IEC61010-2-031 ...more

If the voltages you need to measure are above the specifications of the general purpose probe, B+K Precision has higher voltage probes for you. X1000 Attenuation# 100M ohms / 1pF Input Impedance# 50MHz Bandwidth# 80" (2.0m) Cable Length ...more

250MHz Bandwidth# X100 Attenuation# 48" (1.2m) Cable length# Includes a full accessory kit with a Sprung Hook, Replacement Tip and BNC Adapter.# IEC61010-2-031 ...more

Grey colored probe body# 6/150MHz Bandwidth# X1, X10 & REF Switchable attenuation# 48" (1.2m) Cable length# Includes a full accessory kit with a Sprung Hook, Replacement Tip and BNC Adapter.# IEC61010-2-031 ...more

VPCs Wire Plus program is designed to enable quick and easy custom test system configurations by providing finished system cable solutions in modules; wired, PCB, breadboard and umbilical cords . This eliminates the time and expense of hand-crimping each contact and promotes rapid integration of your Mass InterConnect system with virtually any ...more

If the voltages you need to measure are above the specifications of the general purpose probe, B+K Precision has higher voltage probes for you. 40,000VDC or 20,000Vac Max input voltage# X1000 Attenuation# 1000M ohms Input Impedance# 60Hz Bandwidth# 48" (1.2m) Cable Length ...more

Enclosure, ITA, 90 Series, 6 Module with 2 Cable Clamps ...more

Enclosure, ITA, 90 Series/2100 Series, 10 Module with 3 Cable Clamps ...more

All purpose demodulator probe, usable with most oscilloscopes. Features light weight design and 48" (1.2m) coaxial cable. 100KHz to 950MHz Bandwidth# +3dB Accuracy# 200V Max input voltage# 50VeffHF Voltage# 250mV Actuating voltage# 5pF Input capacitance ...more

The iCon ITA's small width and inboard handle increase the side to side stackability. The U-Shaped Cable clamp allows modules to be pre-wired before assembly and can hold cable bundles up to 0.92 sq in. The slide off cover allows easy access to wiring for maintenance and probing. Protective Cover included. ...more

Red colored probe body# 6/150MHz Bandwidth# X1, X10 & REF Switchable attenuation# 48" (1.2m) Cable length# Includes a full accessory kit with a Sprung Hook, Replacement Tip and BNC Adapter.# IEC61010-2-031 ...more

If the voltages you need to measure are above the specifications of the general purpose probe, B+K Precision has higher voltage probes for you. X100 Attenuation# 100M ohms / 5pF Input Impedance# 200MHz Bandwidth# 48" (1.2m) Cable Length ...more

Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106). ...more

CATV TDR (Cable Fault Locator GAO6110 ) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints. TDR test port is used to transmit the electrical pulse energy from the cable fault like points where there are short circuits, open circuits or high resistance joints. The pulse now travels with th ...more

DS6130 TDR (Cable Fault Locator) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints. ...more

The Noyes OPM5 optical power meter from AFL Telecommunications may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 5 also measures insertion loss of multimode or single-mode cables. The OPM5 offers Wave ID, automatic wavelength identification and switc ...more