Cable Test

The Model 1685 is a headend/hubsite RF eight-carrier generator. Each CW carrier can be activated individually or simultaneously. The RF carriers generated are extremely clean and stable, thus making the 1685 an ideal instrument for testing/aligning the CATV forward band. ...more

The PC-2 is a compact, temperature-stable two RF-carrier source. It is designed to be used for activating and testing the return-band. When used with a signal level meter, the PC-2 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.  ...more

For testing cables, harnesses and other multi-point products and components. Products requiring AC/DC Hipot testing and high insulation resistance measurements. For stand alone measurements or integration into an automated system. Capable of providing highly customized testing programs. Eight models to choose from to fit your test requirements ...more

The Fluke 1550B is a digital insulation tester capable of testing switchgear, motors, generators and cables at up to 5000 V DC. It can be used for a wide range of tests: from simple spot checks to timed tests and breakdown tests. Measurement storage and PC interface software make it ideal for preventive maintenance. ...more

MSRP $175.00 The model 206 cable tester is a stand alone test device. It is designed to test popular PC data cables, printer, monitor, modem, mouse extension, game, BNC coax, RJ45, 1394, and USB cables by identifying the wire connection status: open, short, cross, miswire, and continuity of wires and pin configuration. It is a very good tool f ...more

The 231A can easily read the correct pin configuration of 10BaseT cable (category 5), 100BaseTx, 10Base2 cable (coax) and RJ45/RJ11 modular cables, 356A, TIA 568A, TIA 568B and Token Ring cables by comparing one transmitting end to the corresponding receiving end. With the remote kit, it can test cables installed far away either on wall plate ...more

The B+K Precision Model 205 Universal Cable / Harness Tester tests just about any cable or harness in fractions of a second. It is a compact, stand alone unit that can be used for any type of wired assembly. Opens, shorts and miswires are detected immediately. The universal adapter card offers outstanding flexibility and convenience, ready to ...more

The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA 568A, TIA 568B, and Token Ring cables within a few seconds. It detects miswiring, polarization, and continuity. The 230A also tests the ground of shielded twisted pair cables. With the remote unit, you can remotely test installed cable either from the wall plate or pat ...more

A wire harness tester, a cable tester, a continuity tester, a component tester and a guided harness-assembly aid are all good descriptions of the Easy-wire CR tester. The easy-wire CR features powerful Windows-based software that allows you to create custom on-screen graphics of your connectors and it lights LEDs to guide the harness assembly ...more

Cable and harness tester, with its' user-friendly interface and large clear display, carries on the Cirris tradition of easy-to-use, low-cost, portable hipot testers. The large display, coupled with a sensible and easy-to-understand button interface, makes the setup and testing of cables quick and intuitive. Test Points: 128-1024, Hipot Range: ...more

Find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye cable testers and harness testers have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer one-second pass/fail testing for production environments. Quickly locate i ...more

VPCs Wire Plus program is designed to enable quick and easy custom test system configurations by providing finished system cable solutions in modules; wired, PCB, breadboard and umbilical cords . This eliminates the time and expense of hand-crimping each contact and promotes rapid integration of your Mass InterConnect system with virtually any ...more

Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106). ...more

The Noyes OPM5 optical power meter from AFL Telecommunications may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 5 also measures insertion loss of multimode or single-mode cables. The OPM5 offers Wave ID, automatic wavelength identification and switc ...more

The Noyes HiLite and VFI 2 products from AFL Telecommunications are compact but powerful visible red laser sources designed to troubleshoot faults on fiber optic cables. Light generated by these units will escape from sharp bends and breaks in jacketed or bare fibers, as well as poorly mated connectors. They can identify faults in fiber optic ...more

The Gigabit SuperLooper quickly and easily checks the RX/TX pairs of 1000base network cables, helping a network technician determine if a network signal exists or if there are broken or shorted wires within the cabling (See Specifications). It can be plugged directly into an Ethernet wall port or can be attached to the end of a network patch cable. ...more

The SuperLooper™ T1/E1 Loopback Jack and Plug quickly and easily checks the RX/TX pairs of T1/E1 circuit cables helping a network technician determine if a signal exists or if there are broken or shorted wires within the cabling. It can be plugged directly into a T1/E1 CSU/DSU or can be attached to the end of a network patch cable. ...more

By adsorbing many high-tech achievements, GAO-8B, as a portable and multi-functional automatic communication cable-fault tester, is widely chosen by the line-checking workers to accurately localize the fault and also applied in the fields of measurement and acceptance of line engineering and the works of line maintenance and the checking of el ...more

Wiring Diagram Test to Validate Cable Link SequenceNetwork Layer TestCable Length Test, Maximal Distance is 150mPPPoE DialingDMM Test Touch ScreenSystem Software Upgrade ...more

CATV TDR (Cable Fault Locator GAO6130) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints.What is the principle of TDR TDR test port is used to transmit the electrical pulse energy from the cable fault like points where there are short circuits, open circuits or high resistance joints. Th ...more

The SuperLooper™ ISDN (PRI) Loopback Jack and Plug is used to check ISDN (PRI) cabling for broken or shorted wires and network interfaces for the simplest functionality. When installing primary network backbone circuits, the simple check of an ISDN (PRI) interface or jumper cable using the SuperLooper™ ISDN (PRI) Loopback Jack and Plug can save hou ...more

The SuperLooper™ ISDN (BRI) Loopback Jack and Plug is used to check ISDN (BRI) cabling for broken or shorted wires and network interfaces for the simplest functionality. When installing primary network backbone circuits, the simple check of an ISDN (BRI) interface or jumper cable using the SuperLooper™ ISDN (BRI) Loopback Jack and Plug can save hou ...more

The Patch Test quickly tests Ethernet patch cables for continuity and common wiring standards such as Gigabit Ethernet, Fast Ethernet, and fast Ethernet Crossover. Remote testing of longer cables whose ends are not co-located can be accomplished by using a Smartronix Gigabit SuperLooper Loopback jack to test for Gigabit and Fast Ethernet cables in ...more

The Series 90L4 and Series 90H8 provide the PC-based power of the larger Series 90, but in an economical package for users who do not require more than 512 test points. Both analyzers are designed to operate under the control of your PC. The Series 90L4 is a low-voltage system expandable from 128 to 512 test points in 128-point increments. ...more

The SLM1453I provides you with a full-featured signal level meter that is tunable from 5 - 878 MHz, plus provides you with full signal leakage and ingress testing capabilities at an affordable price. All channel/frequency tuning - measures VHF/UHF, cable and sub-band TV channels. Fully auto-ranging for level measurements from -45 dBmV to +65 dBmv ...more