Cable Fault Locators

The Noyes HiLite and VFI 2 products from AFL Telecommunications are compact but powerful visible red laser sources designed to troubleshoot faults on fiber optic cables. Light generated by these units will escape from sharp bends and breaks in jacketed or bare fibers, as well as poorly mated connectors. They can identify faults in fiber optic ...more

DS6130 TDR (Cable Fault Locator) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints. ...more

CATV TDR (Cable Fault Locator GAO6110 ) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints. TDR test port is used to transmit the electrical pulse energy from the cable fault like points where there are short circuits, open circuits or high resistance joints. The pulse now travels with th ...more

DS6110 TDR (Cable Fault Locator) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints. DS6110 is portable and convenient and easy to use, has maximum range of 1200 meters. DS6110 comes with measure detector, carrying case, two 1.2V/1.2AH Ni. - MH Batteries, charger, user manual and quality ...more

Measurement range: 1~6,000m Resolution (min): 20cm Accuracy: =±2% Impulse width and voltage range: 30ns~3µs,24V VOP range: 50~300m/µs Measurement range type: 50m,100m, 200m, 800m, ...more

CATV TDR (Cable Fault Locator GAO6130) is used to locate any kind of RF cable faults like short circuits, open circuits or high resistance joints.What is the principle of TDR TDR test port is used to transmit the electrical pulse energy from the cable fault like points where there are short circuits, open circuits or high resistance joints. Th ...more

The acoustic pinpointing fault location system Kamphone is a ground sound microphone and is used for pinpointing of flashover faults in power cables. It consists of a receiver, a sensor and headphones. Three search methods are available: acoustic pin-pointing, coincidence and relative distance measurement. The display of the receiver can be used t ...more

The reliability of the daily used and proven cable test van InterCable FOF permits the fast and exact fault location, cable test and diagnosis in low, medium and high voltage networks. The conjunction of the modernest cable measuring methods enables a precise localization and characterization of cable faults. With these systems power networks can b ...more

An easy-to-use fault locator, cable and wire manager and tone generator. Instantly measures distance to open or any fault from one end of any cable pair. Additional line cord options available for coaxial cable (F-connectors) and other applications  ...more

You can diagnose and repair simple fiber link problems with Fluke Networks' VisiFault Visual Fault Locator (VFL). The laser-powered VisiFault locates fibers, verifies continuity and polarity, and helps find breaks in cables, connectors and splices.  ...more

Traces live wires buried or hidden behind walls up to 13 feet deep - Traces unenergized and open (broken) wires - Performs tests without having to interrupt power - Locates breakers, neutral and ground lines - Locates and traces wires in walls, floors, conduit, computer cables, etc. - Pinpoints shorts, ground faults and broken wires - Does not ...more

Pen style optical fiber fault locator. The FC-2005 Fiber Checker Pro is used for checking the defects of a fiber cable. It sends a visible 650nm wavelength red laser light though a fiber optic cable, the breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area. ...more

The Fault Mapper Model CA7024 is a hand-held, alphanumeric, TDR (Time Domain Reflectometer) Cable Length Meter and Fault Locator, designed to measure the length of electrical and communication cables.  ...more

This instrument  has been designed to measure the distance to resistive faults in any type of metallic cable. It works on the principle of measuring the resistance of the two sections of the faulty conductor ratiometrically using a "Kelvin" configuration of four wires, thereby eliminating errors caused by test lead resistance.   ...more

The OS405 (635nm) visible laser cable fault locator allows the operator to find faults in fiber optic cables, even in the OTDR dead zone, optimizing splices and tracing fibers. By injecting a bright red visible light in the fiber, locations of losses such as breaks, bends, or bad connectors can be detected visually, even through the typical ye ...more

The Biddle CFL800E is a multifunction instrument combining several fundamental tests in one practical, field craft test set. Integrated voltage meter, insulation tester, time domain reflectometer and automatic resistance bridge, provide the test functions for basic cable verification and fault locating on twisted pair, quad and coaxial cables. Trad ...more

The L1050 Portable Locator is a one-piece design that is lightweight and highly accurate. Operating the receiver at multiple frequencies optimizes performance for the specific needs of the user with accurate long or short range locates. The flexibility of the unit allows high power operation at low frequency to solve the difficult multi-point groun ...more

The FIS Pocket Fault Locator is a rugged and lightweight, just 7.1" in length and only 4.5oz.  The universal adapter accepts any 2.5mm ferrule, allowing 650nm laser light to be injected into a fiber.  This light enables breaks or sharp bends in a cable to be identified 6-7km away on singlemode fiber, 4-5km away on multimode fiber.   ...more

The Model 60 Long Distance Fiber Fault Locator detects fiber breaks over distances up to 50 km and longer.  The detector wand held near the cable emits a continuous tone when a fiber break or micro-bend is detected.  ...more

The A799 is AGM Elettronica's most advanced fault locator. It can carry out a wide range of routine tests on both telephone and control cables. Tests performed include measurement of cable length,  resistance, capacitance, unbalanced resistance and unbalanced capacitance of  pairs.   ...more

The PFL-4000 Power Fault Locator System is specifically designed to meet power industry requirements in a compact, yet powerful solution for underground residential distribution (URD) topologies.  ...more

In conjunction with T-602 Audio Frequency Generator or T-302 HV Surge Generator, to quick and precisely pin point high/low resistance and flashover fault position for power cable, and detect the cable path and depth ...more

In conjunction with T-505 Pinpoint Fault Locator, T-602 Audio Frequency Generator can precisely pin point low resistance fault position and detect the cable path. ...more

Pen style optical fault locator with 2.5mm to 1.25mm adapter. The FC-2005 Fiber Checker Pro is used for checking the defects of a fiber cable. It sends a visible 650nm wavelength red laser light though a fiber optic cable, the breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area. ...more

The live locator EF 24/200 is mainly used as an adjustable, fast electronic fuse in low voltage power cable distribution networks. In combination with the pulse reflection test set IRG 2000 it allows high resistance and intermittent faults to be located on live cables even with connected consumers. The live locator can be used as a surge switch ...more