Cable Assembly

The iCon ITA's small width and inboard handle increase the side to side stackability. The U-Shaped Cable clamp allows modules to be pre-wired before assembly and can hold cable bundles up to 0.92 sq in. The slide off cover allows easy access to wiring for maintenance and probing. Protective Cover included. ...more

VPCs Wire Plus program is designed to enable quick and easy custom test system configurations by providing finished system cable solutions in modules; wired, PCB, breadboard and umbilical cords . This eliminates the time and expense of hand-crimping each contact and promotes rapid integration of your Mass InterConnect system with virtually any ...more

Identifies unlabeled or mislabeled wire in new installations. Identifies existing network wires to determine the location of workstations or phone lines on a patch panel. Includes ABS™ Tester, ABS™ Signal Thrower, lead set and cable assembly. ...more

Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. ...more

The Ribbon Cable Tester is designed to test the most commonly used flat IDE cables for wiring continuity, opens, shorts and miswiring. An intelligent CPU will memorize the correct wiring configuration for an IDE cable, thus enabling mass production cable assemblies to test one cable after another for pass or fail status. ...more

One-slot cable extender to connect the extra 50-pin male breakout connector of an SCXI cable assembly to an SCXI-1181 breadboard module installed in an adjacent slot ...more

Screw-terminal connector with strain relief as well as a D-Sub solder cup backshell for creating custom cable assemblies. ...more

WEETECH offers complete solutions, which besides the test electronics comprise adaptation solutions for cables, backplanes, racks and electronic assemblies. With the daisy chain matrix the test points have contact where the test is going on: at the backplanes, in the card magazines and racks. ...more

The high sensitivity and high resolution of Endevco?s model 65 distinguish this triaxial accelerometer from comparable products. The Endevco® model 65 is packaged in a 10-mm cube of welded titanium construction. Interface to the model 65 is via a Microtech 4-pin connector. Temporary petro-wax adhesive and a ten-foot cable assembly with BNC co ...more

SCXI cable assemblies connect the I/O connector of a plug-in DAQ board to the front-end signal conditioning SCXI system ...more

SCXI cable assemblies connect the I/O connector of a measurement device to the front-end signal conditioning SCXI system ...more

SCXI cable assemblies connect the I/O connector of a measurement device to the front-end signal conditioning SCXI system ...more

Cable assembly ...more

SCXI cable assemblies connect the I/O connector of a plug-in DAQ board to the front-end signal conditioning SCXI system. ...more

The HPCC-iDB software fully automates the vector network analyzer specifically for testing high performance coaxial cable in aerospace and defense vehicle applications.  Measurement parameters include VSWR, Insertion Loss and Phase.  The software completely automates the testing with easy-to-use GUIs.  Special features include Phase Matching, ...more

Wilcom T124 Cable Shield Splice Tester is an accurate measuring device which provides measurement of the conditions existing at cable shield splices, checks the integrity of ground connection, and checks the condition of capacitors across insulated splices. Two probes, capacitively coupled to the shield of the cable under test, are connected t ...more

Size 00 probe for coaxial contact pin replacement. 18GHz Microwave switches and microwave cables assembly. ESD protection includes ionized fan and discharge before test function to prevent TDR meter from damage. ...more

Q-Series Noise Dosimeters are comprehensive tools for measuring occupational, industrial, and environmental noise. Quest noise dosimeters consist of a compact and rugged lightweight noise meter assembly that clips to a person's belt and a small cable mounted pendant microphone that fastens to the person's collar, close to the ear. ...more

The rugged Model LL-V vertical entry submersible liquid level sensor from Honeywell Sensotec can be suspended in an open tank or attached to the crown of an enclosed tank and used to any depth. The atmospherically vented oceanographic cable assembly exits through a 1/2-14 NPT threaded conduit connection that allows mechanical or chemical protection ...more

Copper Cables for NI GPIB-130 Extender - Indoor plenum-rated cable assembly (up to 300 m) ...more

Screw-terminal connector with strain relief as well as a D-Sub solder cup backshell for creating custom cable assemblies. ...more

ProfiPulse is a low cost tool to assist with the validation of installed PROFIBUS DP cable. It can verify if the cable is suitable for the required transmission speed. When an installer has finished the cable assembly, he will in most cases test it with a handheld tool. These tools can only check the static faults, but not the high speed dynami ...more

The Model 1260-155/A/T/AT is a high-frequency, coaxial 1x4 binary tree switch card for use in either the 1260-100 VXI Carrier or the Model 1256 GPIB/RS-232 Switching Mainframe. These switch cards are designed with an MCX interface connector, which is known for its high signal fidelity with connectors and cable assemblies available from many di ...more

Screw-terminal connector with strain relief as well as a D-Sub solder cup backshell for creating custom cable assemblies. ...more

Developed under license from the National Aeronautics and Space Administration (NASA), the ESP meter uses Standing Wave Reflectometry to locate faults in cables and harness assemblies. This microprocessor controlled tool provides the most accurate fault location results available today, no question, no doubt ...more