Bare Board Test

The 050-05 series probes and sockets are designed for bare board testing. .050 (1.27) Centers - .050 (1.27) Stroke. ...more

The 025-16 series probes and sockets are designed for bare and loaded board testing. .025 (0.63) Centers - .160 (4.06) Stroke. ...more

TE-10K bed of nails style test fixture. Completely self contained. PC style passive back plane with plug in data acquisition boards. Programmable with National Instruments Labview or Labwindows CVI. Can be configured to create a complete full performance cost efficient functional, in-circuit, or bare board tester. ...more

Test Electronics will customize the TE-4000 bed of nails style test fixture for your circuit board and test application. Next, add a test engine or a simple desktop or rack mount computer, plug in the data aquisition boards and software. This will create a complete full performance cost efficient functional, in-circuit, or bare board tester. ...more

Simple Low cost Bed of Nails Clamshell style Circuit board test fixture. Drill it yourself, or let Test Electronics prescision drill and customize the TE-1100 bed of nails style test fixture for your circuit board.  ...more

Simple Low cost Bed of Nails Clamshell style Circuit board test fixture. Test Electronics will prescision drill and customize the TE-1000 bed of nails style test fixture for your circuit board.  ...more

Test Electronics will customize the TE-3100 bed of nails style test fixture for your circuit board and test application. Next, add a desktop or rack mount computer, plug in the Data Aquisition boards and software. This will create a complete full performance cost efficient functional, in-circuit, or bare board tester. ...more

Test Electronics will customize the TE-3000 bed of nails style test fixture for your circuit board and test application. Next, add a desktop or rack mount computer, plug in the data aquisition boards and software. This will create a complete full performance cost efficient functional, in-circuit, or bare board tester. ...more

Bare Board Test Series. Test Center: .075 (1.91) ...more

The 100-05 series probes and sockets are designed for bare board testing. ...more

Pack the TE-500 test fixture up in a briefcase with your laptop computer and perform functional, in-circuit, or bare board testing on site at any location! Visit your overseas supplier and check your circuit boards as they roll off the assembly line. ...more

Level IV High Pin Count Backplane Test System. Isolation testing exceeding Bellcore standards. Continuity testing down to .01 ohms. Fully programmable thresholds. Resistors, Capacitors & Inductors. Diodes, LEDs, Zeners & Transistors. Vectorless: Diode Junction Scan. Vectorless: HP (Agilent) TestJet. Missing & Bent Pins. Connector Orientation & Key ...more

Test Electronics will customize the TE-9000 bed of nails style test fixture for your circuit board and test application. Next, add a Genrad 2270/71/72/75/76/8X or a Hewlett/Packard 3060/61/62/65/70/72/75 or a Teradyne 800/10/75 & 1800/10/20 or a Checksum, TTI, Testronics, or any other MDA This will create a complete full performance cost e ...more

SuperSpeed Bare Board Tester ...more

Bare Board Test Series. Test Center: .025 (.65) ...more

Universal bare board tester ...more

Test Electronics will customize the TE-2000 bed of nails style test fixture for your circuit board and test application.  ...more

The 100-16 series probes and sockets are designed for bare and loaded board testing. ...more

 The Zeus wireless test fixture merges rigid pin and dedicated fixturing technologies to test bare or loaded boards on most test systems with high density sping probe test interfaces.  ...more

Bare Board Test Series. Test Center: .50 (1.27) ...more

This tester is the ideal tester for prototyping or very small lot testing. With this machine up to 1350 testpoints per minute can be tested. The accuracy and the repeatability permit a test of boards with a pitch of 6mil and a pad size of 3mil. This machine was designed with the most simple handling and operation for the operators in mind.&nbs ...more

The TE-1300 bed of nails style troubleshooting fixture is designed to take highly unbalanced (off center) loads so that a single board can be placed on one side or the other. This configuration provides probing and tweaking access to both sides of the board uder test through cutouts in the clear top plate. Next, add a desktop or rack mount com ...more

The FC16-2, 1 and 2 Gbps edge switches are an entry point to the switched storage environment with up to 16 self-configuring ports. Like the enterprise class director, it supports class 2,3 Fibre Channel and optical and fiber GBICS, and has dual power and a GUI control. The FC/9000 provides low cost of entry with the ease of a hub and the aggr ...more

PCB Tester ...more

Back Plane and Bare Printed Circuit Board Universal Grid Tester. ...more