Backplanes

The Series 90HV combines low-voltage solid-state technology with high-voltage relay technology ¾ solid-state devices for testing continuities and components at low voltage; relays for testing high-resistance isolation and high-current continuity. The high-resistance isolation tests are typically used to test the quality of harness insulation m ...more

The Elma Bustronic 7U VME64x backplane series is designed to fully comply with the ANSI/VITA VME extension standard. The extra 1U of height provides room for extra power bugs. The 7U version is also compliant to the VITA 1.7 Increased Current Specification.  ...more

The EasyPlug CompactPCI backplane line has 47-pin pluggable connectors in either a vertical (3U or 6U) or horizontal (9U) orientation. This reduces mean-time-to-repair (MTTR) and time-consuming cabling costs. ...more

Digital Backplanes allow easy digital input and output expansion for large systems. Backplanes typically are used with Industrial Enclosures, which provide electrical shielding and a provide a compact unit for multiple external boards. ...more

Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical. ...more

C-TAC Plus for AN/AYK-14 is an embedded system analyzer. It provides simultaneous Real-Time Non-Intrusive (RTNI) monitoring of all key points in the system. The monitoring is done on a completely non-intrusive basis without the injection of wait states or cycle stealing, and does not affect bus timing or message sequencing. ...more

With its versatile design, the Omni8300BT can provide fast and accurate low voltage testing of a wide variety of products including cables, harnesses, backplanes and equipment racks. ...more

Wallmount/Rackmount, 3U/6U, 19 inch enclosures, backplanes and power supplies ...more

MicroTCA Backplane for subrack enclosures. Star or Dual Star versions are standard. Mesh configurations available upon request.  ...more

The ISA Half Card Single Board Computers are highly integrated boards, for use in ISA passive backplane systems. They range from moderate to high computing power, with low power consumption/fanless operation ...more

Elma Bustronic is the leader in high-performance ATCA backplane design. The Dual Star backplane design has been optimzed via signal integrity studies.  ...more

Kontron offers a comprehensive range of boards to give system designers expanded options for integrating embedded processors within a variety of platform configurations including, but not limited to, PICMG 1.2, 1.0 full size and half size cards, and backplanes. ...more

The VME320 backplane offers true 320 Mbytes/sec. bandwidth. In the VME320, a sigal is driven from slot 1, goes to the middle slot and then radiates out to all other slots. All the capacitance concentrates at the middle slot instead of having a transmission line effect like a conventional shared-bus backplanes. ...more

C-TAC is an embedded system analyzer. It provides simultaneous Real-Time Non-Intrusive (RTNI) monitoring of all key points in the system. The monitoring is done on a completely non-intrusive basis without the injection of wait states or cycle stealing, and does not affect bus timing or message sequencing. C-TAC also provides timecorrelation of ...more

The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor. ...more

The Low Profile line has power studs between the slots to provide the most compact backplanes available. The backplanes can pack more slots into smaller, low profile horizontal chassis. The 6U line comes in standard cPCI, PICMG 2.16 (Compact Packet Switching), and PICMG 2.17 (StarFabric) options. The 7U versions have various cabling and plugga ...more

Ideal for adding specific RF and Microwave modules into a VXIbus system. The 7066 decouples and filters the VXI chassis backplane power lines for use within the shielded enclosure. ...more

The DP-VXI-4503 is a 80 channel, one form C (SPDT) relay switch module. It occupies only one VXI slot. The each of the two contacts in every relay is used to provide status of the relay through read back and switching purpose. The module features a backplane trigger for VXI triggered operation and also software trigger. ...more

The J2 and J3 backplanes are ideal for prototyping. With all J2 pins undefined (except the B row) the J2 backplane allows flexibilty for testing and designing your system. The J3 development backplane has defined A+C rows as power, with B row remaining user-defined.  ...more

The EasyCable cPCI backplanes have power nuts along the right side of the backplane for easy cabling access. They come in both 3U and 6U heights. The 6U version standardly comes with an ATX connector in the rear and has options for H.110 for Computer Telephony.  ...more

Nexxim is an advanced, frequency- and time-domain circuit simulator for engineers designing the next generation of high- performance DigitalRF CMOS ICs, GaAs/SiGe RFICs, SIP/SOC packages, power delivery systems and gigabit computer and communication backplanes. ...more

All Elma Bustronic VME backplanes are designed to maximize performance, minimize noise, and to give the customer the most reliable, cost-effective product possible. To achieve this we use 8-layer construction, strip-line design, decoupling capacitors at every slot, inboard terminators, heavy power and ground planes, transient analysis simulati ...more

The Elma Bustronic VXIbus backplane series are designed to fully comply with the VXIbus specifications, Rev. 1.4-5/92. Elma Bustronic has incorporated a feature set that is unique in the industry: a custom, laminated busbar, active or passive terminations, automatic active BUSGRANT and IACK jumpering, and optional AMP enhanced Eurocard connect ...more

The Elma Bustronic 6U VME64x backplane series is designed to fully comply with the ANS/VITA VME extension standard. We provide all standard features required for VME64x compatibility, including 160-pin VME extension connectors in J1 and J2, all defined ground pins connected to a ground plane, routing and termination of all VME and VME64x busse ...more

CompactPCI chassis and backplanes for both 3U and 6U cPCI boards (non 2.16) ...more