Amplifiers

The 6060 is a two-channel signal conditioning amplifier-digitizer module with 50 kHz or 100 kHz bandwidth and both digitized and analog outputs. The bridge input is ten-wire shielded with programmable constant voltage or constant current excitation and programmable completion for quarter, half and full bridge transducers. Automatic bridge bala ...more

Model 6036 is a four-channel, programmable charge amplifier, filter and digitizer with a second input for piezoelectric sensors with integrated electronics (IEPE). The high-performance charge amplifier can be used to measure dynamic acceleration, pressure, force and strain from piezoelectric transducers. Two charge-to-voltage input ranges opti ...more

The 6037 has eight channels of strain gage or transducer signal conditioning amplifiers and digitizer. Each channel has programmable voltage excitation, programmable bridge completion and automatic balance, programmable gain instrumentation amplifier, four-pole low-pass filter and sample and hold amplifier. The amplified channel outputs are mu ...more

Two channels of high-performance signal conditioning amplifiers for quarter, half and full bridge transducers. May also be used for RTDs, potentiometers, dynamic strain, voltage and voltage mode (ICP type) charge transducers. Each channel has programmable voltage or current excitation, autobalance, voltage and shunt calibration, differential i ...more

The 28608A Octal Programmable Filter/Amplifier Card is ideal for conditioning low-level voltage inputs in front of high-resolution digital data acquisition systems. Low-pass, high-pass and band-pass configurations are available. Programmable pre- and post-filter amplifiers provide an overall gain of 2048. The 28608A allows for up to 128 channe ...more

The PF-1UA-16FA is a 16-channel filter/amplifier and the PF-1UA-8FA filter/amplifier is an 8-channel, both offering a choice of either 4 or 8-pole low-pass filters or 8-pole band-pass filters. Cutoff settings from 1 Hz to 204.6 kHz are supported. The low-pass filters may operate in either a 'flat' mode for maximally flat pass-band amplitude re ...more

VMEbus fixed frequency and programmable filter products from 1.0 Hz to 2.0 MHz and fixed and programmable amplifier products from -12 dB to +60 dB. ...more

Rackmount Instruments including programmable electronic filters from 0.1 Hz to 300 kHz and programmable gain amplifiers from -12 dB to +60 dB. ...more

Fixed Frequency CompactPCI electronic filter/amplifier cards from 1.0 Hz to 100 kHz. ...more

27304 Quad Dual-Mode Charge Amplifier supports the two common piezoelectric transducer types, charge and voltage (IEPE), providing flexibility for use in a wide range of applications including vibration measurements. Programmable gain of up to x4096 is provided. The 27304 accommodates both isolated and grounded inputs. For integrated circuit p ...more

Fixed and programmable gain amplifier modules and instruments from -12 dB to +60 dB with full power bandwidth to 1.0 MHz. ...more

Benchtop Instruments including programmable electronic filters from 0.1 Hz to 300 kHz and programmable gain amplifiers from -12 dB to +60 dB. ...more

The Precision 28302B Dual Vibration Amplifier is designed to condition signals from rotating machinery. The card accepts inputs from single-ended or differential piezoelectric, IEPE accelerometers or remote velocity sensors. Programmable high-pass and low-pass filters remove unwanted out-band signals from the acceleration and velocity outputs. ...more

The Model 2701A was originally developed for use in the Model 2100 series of Power Calibration and DC Resistance Measurement Systems. Fully programmable, the Model 2701A can be configured as part of a fully automatic current calibration system to optimize throughput and will drive resistive, capacitive and inductive loads. When used as a Trans ...more

The PMC-AD8 module provides a high performance data acquisition subsystem. Octal 16 bit channels, 200 KSPS ADC's. The Local DSP can be used to simply move data samples to the PMCbus or can provide processing functions such as limit checking, FFT's, digital filtering, etc. Software can be downloaded to the DSP via the PMC interface. Instrumenta ...more

The 6035 input module has eight channels of programmable transducer signal conditioning amplifiers and digitizer. Each channel has programmable voltage excitation, bridge completion and balance, programmable gain instrumentation amplifier, four-pole low pass filter and sample and hold amplifier. Channel outputs are multiplexed and digitized to ...more

The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses. ...more

Each Gator Transmitter is housed in a high impact ABS water-resistant case. It has a built-in agile frequency synthesizer, dynamically controlled power amplifier and a built-in modem and DTMF (touch-tone) decoding allowing remote control of all transmitter parameters via a phone line or cellular telephone. Remote adjustments include the power ...more

The ANSI-95 16-channel Zebra II is an excellent baseband W-CDMA and Multi-tone source to test power amplifiers as per IS-97. Sixteen data-encoded CDMA channels are digitally combined with a user selectable mixing ratio. The combined output is band limited with digital and analog filters and output as ANSI-95 baseband I and Q signals with > ...more

The dS-LPF is a passive 20kHz low-pass filter in 2 or 4-channel configurations designed primarily for measuring digital power amplifiers. The Passive Low-pass Filter is intended to aid measurement of switching ('Class D', or 'PWM') power amplifiers where the presence of shaped and switching noise outside the audio band can adversely affect the ...more

The PC-1 is a compact, temperature-stable RF-carrier source. It is accurate enough to calibrate spectrum analyzers, signal level meters or any other receiving devices. When used with a signal level meter, the PC-1 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method. ...more

The PC-2 is a compact, temperature-stable two RF-carrier source. It is designed to be used for activating and testing the return-band. When used with a signal level meter, the PC-2 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.  ...more

The NPRT 2200 performs Noise Power Ratio measurements to determine the dynamic range of optical transmitters, amplifiers and other active devices used in HFC networks. It has an internal broadband noise source, selectable filters and a measuring receiver. ...more

8-Channel Simultaneous-Sampling Differential Amplifier Module ...more

AG 1012 offers up to 1000 Watts RF Power From 20 kHz to 6 MHz for Industrial and Laboratory Application. Data acquisition: analog port for status monitoring and power measurement. RS232 communication: full control of all amplifier and generator functions. ...more