AC Current Clamps

The 301 is intended to be used with an AC Current Clamp Meter. It provides temporary separation of conductors to facilitate measurement of current. Most 120Vac devices use a two conductor power cord which makes it difficult to isolate a single conductor to make a current measurement. A single conductor is required to make a measurement because ...more

Fluke Current clamps are the ideal tools to extend the functionality of Fluke tools. The i400 is a single range 400 A ac current clamp with current output via safety shrouded banana plugs. The clamp is compatible with most Fluke multimeters or any other current measurement device that accepts 4mm-shrouded banana plugs and has an AC milliamp ra ...more

Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools. Battery-powered Hall-effect probe measures 1A to 400 A. 1mV/Amp output guarantees easy reading on your meter. Take accurate current readings without breaking the circuit. Maximum conductor Ø 32 mm. ...more

Fluke Current clamps are the ideal tools to extend the current ranges of Fluke tools. Battery-powered Hall-effect probe measures 1 A to 1000 A. 1mV/Amp output guarantees easy reading on your meter. Take accurate current readings without breaking the circuit. ...more

Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment - saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence ...more

digital clamp meter. 3 1/2 LCD display with automatic polarity indication data-hold function. AC current measurements: max. 1000A. insulation test: max. 2000Mohm (if used with optional DCMIT). voltage measurements: AC (max. 750V) and DC (max. 1000V). resistance measurements: max. 20Kohm ...more

600 A AC current capability. Large optically clear window. Ohm scale on dial drum. Range finder symbols. Broad frequency response - 50 to 400 Hz. ...more

AC/DC current measurements. True RMS. Measures up to 660A. TightSight™ bottom display. Voltage-presence warning on all functions. Tapered jaws with hook tip. Peak Max/Min (1ms). Audible continuity. ...more

3 2/3 digit (2400 counts) LCD display with white LED backlight. 18mm (0.7") jaw opening. 0.1-200A current measurement. built-in non-contact AC voltage detector. incorporated flashlight. frequency measurement 40Hz-1kHz. autoranging with auto power off. data-hold function ...more

digital clamp meter. 3 ½-digit LCD display with automatic polarity indication. data-hold and backlight function. AC current measurements: max. 200A (via transformer jaws). AC voltage (max. 600V) and DC voltage (max. 600V) measurements. resistance measurements: max. 2Kohm ...more

Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement  up to 600 A.Relative measurement. One touch auto zero. ...more

Small jaw: 1.2"(W) x 0.53" (D) (300x13.4mm). Clamp opens up to 1/2  inch  (12.5 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement from 0.001 up to 100 A. Relative measurement. One touch auto zero ...more

The Clamp-On Simple Logger Model CL600 is a self-contained data logging AC current probe. The logger requires no user setup and has the ability to automatically adjust its scale and sample rate to optimize themselves to the recording. One button operation makes the clamp-on logger extremely easy and quick to use. ...more

The SR600 Series AC Current Probes are designed for use in industrial and utility environments. The unique ergonomic design allows them to easily clamp onto cables or small bus bars. Excellent transformation and low phase shift, plus a broad frequency response, permit accurate measurements of current for power and power quality measurements. M ...more

LCD display with automatic polarity indication. data-hold function. DCV (max. 1000V) and ACV (max. 750V) measurements. ACA (max. 1000A) current measurements. max. Ø for conductor: 50mm. resistance measurements: max. 2Mohm. requency measurements: max. 20kHz. temperature measurements: 0°C to 750°C. diode test, continuity test and backlight. K-typ ...more

Non-contact. Shaker mode to verify AC voltage. Clean power indicator. Capacitance. Cat III - 1000V rated. 200A Current capability. Audible continuity. Diode Test. Data hold/max hold. Low battery indicator. Overload protection on all ranges. Silicone leads. Audible dangerous voltage warning. ...more

The TRMS Clamp-On Leakage Current Meter Model 565 is designed to measure low AC currents, which are typically leakage currents in ground conductors. Low currents are measured using either 60mA or the 600mA range.  ...more

display: digital and analogue display, 3200 counts and 33-segment bargraph, digit height 15mm. data-hold function. DCV (max. 1000V) and ACV (max. 750V) measurements. ACA and DCA (max. 1000A) current measurements. max. Ø for conductor: 50mm. resistance measurements: max. 30Mohm. frequency measurements: max. 30kHz ...more

The AmpFlex is a flexible AC current probe composed of a flexible sensor and an electronic module. The flexible sensor permits measurements on conductors where standard clamp-on probes cannot be used. Measurement range is 5 to 3000A.  ...more

The Fluke 321 and 322 are designed to verify the presence of load current, AC voltage and continuity of circuits, switches, fuses and contacts. These small and rugged clamp meters are ideally suited for current measurements up to 400 A in tight cable compartments ...more

The Fluke i1000s is a clamp-on ac current probe designed to expand oscilloscope applications in industrial and power environments. The Current Probe (shown in figure) provides the following features: Ideal for measuring distorted current waveforms and harmonics. Allows accurate measurement of currents from 100 mA to 1000 A rms, 5 Hz to 100 kHz with ...more

Fluke Current clamps are the ideal tools to extend the current ranges of Multimeters. The i200 is a single range 200A ac current clamp with current output via safety shrouded banana plugs. The i200 is compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs. Companion to a DMM to measure up t ...more

Flexible 24" (610mm) probe for Current to 3000A. Easily wraps around bus bars and cable bundles. Fast Peak capture (30µs). Simultaneously displays Frequency with Current or Voltage. ...more

AC Current model to meet your application needs. Compact size allows measurements in tight locations. High accuracy for Current measurements. Autoranging with Auto Power Off. 0.9" (23mm) jaw size accommodates conductors up to 300MCM. Continuity beeper and Diode test. ...more

True RMS Professional Clamp with InfraRed Thermometer for non-contact Temperature measurements. Professional kit includes: EX730: 800A True RMS AC/DC Clamp Meter (0.1A Resolution, ±3% AC accuracy). 480172: AC line splitter enables use of a clamp meter to measure AC Current on a 2-wire or 3-wire power cord to 15A. DV20: Non-contact AC Voltage Detect ...more