Showing results: 1816 - 1830 of 2483 items found.
-
General Tools & Instruments
All psychrometers derive an environment's wet-bulb and dew point temperatures from a precise measurement of relative humidity. The original psychrometer had two thermometers mounted together with a handle attached on a chain. One thermometer was ordinary. The other had a cloth wick over its bulb and was called a wet-bulb. New, digital versionslike General's EP870X family improve on this basic design, offer HVAC technicians a better tool for recharging the refrigerant of a residential or commercial A/C system.
-
AMETEK Drexelbrook
The 28670XX-DRX Series are unidirectional wireless systems that comprise a transmitter and a receiver.This Drexelbrook transmitter accommodates two digital signals in the range from 5 to 30 V AC/DC or 100 to 240 V AC and one analog current signal (4-20 mA). These signals are available for further processing at the receiver in the form of two relay contacts and one 4-20 mA current output. In addition, a third relay in the receiver diagnoses the status of the wireless connection (RF link).
-
MAG-2015AD -
MCH Instruments Co.,Ltd.
Feature:*Signal frequency: 0.1Hz~15MHz, continued*Wave form: square,sine*Output attenuator: 0dB,20dB,40dB,60dB*Output level: 20Vp-p in open ciruit,not less than 10Vp-p with 50Ω load*Rising edge of Square not more than 35ns at 2MHz*Sine distortion less than 1%,amplitude-frequency characteristic ±0.5dB with in 2MHz, ±3dB above 10MHz*Frequency Counter: 20Hz~30MHz*Power supply: AC 220v (110v optional)
-
Georator Corporation
A frequency converter, also known as a frequency changer, is a device that takes incoming power, normally 50 or 60 Hz and converts it to 400 Hz output power. Different types of power frequency converters exist, specifically, there are both rotary frequency converters and solid state frequency converters. Rotary frequency converters use electrical energy to drive a motor. Solid state frequency converters take incoming alternating current (AC) and converts it to direct current (DC).
-
Columbia Research Laboratories
Columbia Research Labs offers our standard Inclinometer System and our Differential Inclinometer System. The standard system includes a temperature compensated force balance inclinometer in conjunction with a power module and convenient digital display. It is available with either AC or DC Power supply input. The Differential System allows the customer to match the slope of two remotely located surfaces. The readout can be set to indicate the absolute tilt of either sensor or the differential angle between them.
-
Bender Inc.
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
AWG18 -
APPLICOS
The AWG18 is an 18 bit Arbitrary Waveform Generator for high-speed / high resolution waveform generation. This module features two dedicated signal paths. A DC to 100 MHz path which is optimized for accurate time domain and frequency domain measurements up to 30 MHz. And a dedicated AC path optimized for signals between 10 MHz to 100 MHz. In combination with the built-in filters it features a typical harmonics level of better than -80 dBc for the whole range.
-
Astronics Corporation
The CorePower® DC or AC Electronic Circuit Breaker Unit replaces conventional thermal mechanical circuit breakers and functions as both a breaker and a switch for controlling loads. By placing ECBUs closer to loads, aircraft manufacturers gain a significant reduction in wire weight, need fewer system components, and lower installation labor costs while increasing safety, efficiency, and reliability. This new smaller unit requires less space and provides more flexible mounting options.
-
287 SVD -
Standard Electric Works Co., Ltd
● Compact, easy to wear and convenient in use.● Usable both indoor and outdoor.● Voltage detection distance: 6.6kV(3.8kV phase to ground) : 40cm ± 20% 11.4kV(6.6kV phase to ground) : 55cm ± 20% 19.7kV(11.4kV phase to ground) : 80cm ± 20% 22.8kV(13.2kV phase to ground) : 85cm ± 20%● Water-proof design. (IP65)● Equipped with self-testing functions.● Able to sense all kinds of AC High Voltage System.● Low power consumption.● CE Certified.
-
Applied Relay Testing Ltd.
When used in conjunction with ART's own parametric relay test systems such as the RT290, the RT900 offers high speed AC and DC Hipot (dielectric withstand voltage) and Leakage testing of relays or other multi-pin passive devices.
-
ACD-50NAV -
Amprobe Test Tools
ACD-50NAV clamp-on power meter offers AC current measurements to 600 A, AC/DC voltage to 1000 V, and wide jaws to accommodate large conductors. This clamp-on multimeter is ideal for industrial power monitoring and verifying system conditions.
-
H301 -
Howell Instruments, Inc.
The H301 Environmental Control System (ECS) Tester measures and displays parameters required to test and troubleshoot aircraft heating and air conditioning systems. These parameters include temperatures, pressures, AC and DC voltages, DC currents, and resistances.
-
1800 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages.● Color-coded scale.● AC voltage measurement.● Fuse protected.
-
1801 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages.● Color-coded scale.● AC voltage measurement.● Fuse protected.
-
CTS Series 3.2 -
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.